Linear LRA - Manual

Table of Contents:

• Page 2 – Table of Contents; WARNING
• Page 3 – Pre-installation Information; Always Check the Gate’s Action; Safety Information and Warnings; Regulatory Warnings; THE FOLLOWING FORMATS ARE USED FOR SAFETY NOTES; IMPORTANT INSTALLATION SAFETY INSTRUCTIONS; TO REDUCE THE RISK OF SEVERE INJURY OR DEATH
• Page 4 – Linear Actuator Operator Overview; AC Power Wiring; MODEL LRA POWER WIRING; The distance shown in the table above is measured in feet from the; DC Control and Accessory Wiring; Control wiring must be run in a separate conduit from power wiring.; Control Box Mounting; When installing the cable connecting the operator to the; USE COPPER WIRE ONLY!; GATE CLOSED; Figure 1. Linear Actuator Operation
• Page 5 – Gate Layout Illustration
• Page 6 – Mounting Bracket Installation; Depending on the gate design, an additional reinforcing; Post Bracket Installation; When installing the post bracket on a round post or masonry; Gate Bracket Installation; Alternate method to locate the gate bracket:; Figure 3. Post Bracket Installation; The gate must be installed in a location so that enough
• Page 7 – Operator Setup; Operator Mounting; Install the washer and clip-ring on the traveler shaft.; Controller Connection; Connect the interface cable to Terminals 1-5 on the Controller (see; AC Power Connection; Do not splice the ground wire. Use a single piece of solid; TRAVELER; Figure 5. Mounting the Operator; Figure 7. Power and Ground Connections; ALL AC ELECTRICAL CONNECTIONS TO THE POWER SOURCE AND
• Page 8 – Limit Switch Adjustment; decreases; Manual Disconnect; Figure 8. Open Limit Switch; CAUTION; Be careful not to damage the limit switch wires while adjusting; Figure 11. Manual Disconnect
• Page 9 – Controller Features; Figure 12. Controller Features
• Page 10 – Indicator Descriptions; APEX FUNCTION DISPLAY INDICATIONS
• Page 11 – Terminal Descriptions; TERMINAL
• Page 12 – Operator Accessory Connections; Figure 13. Operator Accessory Connections
• Page 13 – Basic Controller Programming; The Mid-travel Stop feature is disabled when dual gate
• Page 14 – Run Alarm and Pre-start Alarm; Run Alarm Off and Pre-start Alarm Off; Maximum Open Direction Current Setting; OPEN; button to fully open the gate.; Maximum Close Direction Current Setting; while this function is; CLOSE; button to close the gate.; RUN ALARM
• Page 15 – Advanced Controller Programming; Entering Advanced Programming Mode; input terminal so successive inputs; SINGLE; input can be set to cause the gate to OPEN; Stagger Mode; This function is used in dual gate installations only.; COMM LINK; Stagger Delay Time; This function is used in dual gate installations only.; The factory
• Page 16 – Auxiliary Relay Mode; Power Failure Mode; This function is only used with DC battery backup.; Fail Safe and Fail Secure are disabled if Stagger Mode is; REVERSE
• Page 17 – Soft Start/Stop Duration; Changing the; Reset Cycle Count; button for 2 seconds; Maintenance Alert Trigger; The Controller has a; Mid-travel Stop Position; if the Fire Department input is triggered, if the; Motor Type Selection; DURATION
• Page 18 – ANTENNA
• Page 19 – Loop Layout Illustration; MINIMU
• Page 20 – Safety Edge Layout Illustration; ARNING
• Page 21 – Photoeye Installation Illustration
• Page 22 – Dual Gate Installations; The shield wire should be connected COMM LINK terminal; Dual Gate Enable; Gate Operation; Figure 14. COMM LINK Wiring
• Page 23 – Operation Indications; The Stop and/or Reset button must be located in the line-of-
• Page 24 – Troubleshooting
• Page 25 – Model LRA Replacement Parts; HARDWARE KIT; MODEL LRA ARM MECHANICAL PARTS LIST
• Page 26 – Preventative Maintenance; General; Actuator Body — Wipe down the unit with a clean rag .; -Month Preventative Maintenance; . Inspect all nuts and bolts for proper tightness and tighten; Battery Maintenance; FCC Notice; Always disconnect power from operator before servicing.
• Page 28 – Gate Operator Installation Checklist; OR have