Page 2 - MAIN UNIT PARTS LIST
MAIN UNIT PARTS LIST PART # ACU04-1360 ACU04-1367 ACU04-1361 ACU04-1338 ACU04-1359 ACU04-1358 ACU04-1362 ACU04-1356 ACU04-1355 ACU04-1352 ACU04-1365 ACU04-1364 ACU04-1368 ACU04-1363 ACU04-1354 ACU02-1306 ACU04-1366 ACU02-1294 ACU02-1321 ACU04-1385 ACU02-1320 ACU05-0313 ACU02-1296 ACU01-2028 ACU05-03...
Page 3 - Tools Required for Assembly
BOLT LENGTH Tools Required for Assembly NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. Bolt Length Ruler * 9/16” wrench* Ratchet with 9/16” socket* Metric Allen wrench set 3 LEG PRESS PARTS LIST PART # ACU10-0205 BLK ACU04-1377 ACU04-1378 ACU04-1379 ACU04-1380 ACU04-1381 A...
Page 6 - FIGURE 1
STEP 1: FIGURE 1 6 • LOOSELY assemble the LAT/LOW FRAME (14) to the TOWER BASE (10) using four RH CAPS (69), two 3/8 X 97mm BOLTS (59), four 3/8” SAE WASHERS (66), four 3/8” RH WASHERS (67) and two 3/8” LOW HEIGHT LOCK NUTS (65) as shown in FIGURE 1. 1 0 6 9 1 4 6 6 6 7 6 5 3/8 X 97mm 59 0 1 1/2 1/2...
Page 7 - FIGURE 2
STEP 2: FIGURE 2 7 • LOOSELY assemble the LEG PRESS FRAME (85) to the TOWER BASE (10) using four RH CAPS (69), two 3/8 X 117mm BOLTS (104), four 3/8” SAE WASHERS (66), four 3/8” RH WASHERS (67) and two 3/8” LOW HEIGHT LOCK NUTS (65) as shown in FIG-URE 2. (NOTE: The two 3/8 X 117mm BOLTS (104) for t...
Page 8 - FIGURE 3
STEP 3: FIGURE 3 8 59 3/8 X 97mm 6 5 6 7 6 6 6 9 9 1 0 • LOOSELY assemble the TOWER UPRIGHT (9) to the TOWER BASE (10) using four RH CAPS (69), two 3/8 X 97mm BOLTS (59), four 3/8” SAE WASHERS (66), four 3/8” RH WASHERS (67) and two 3/8” LOW HEIGHT LOCK NUTS (65) as shown in FIGURE 3. (NOTE: REPLACE...
Page 9 - FIGURE 4
STEP 4: FIGURE 4 9 • LOOSELY assemble the MULTI PRESS FRAME (8) to the LEG PRESS FRAME (85) using eight RH CAPS (69), two 3/8 X 117mm BOLTS (104), two 3/8 X 67mm BOLTS (55), eight 3/8” SAE WASHERS (66), eight 3/8” RH WASHERS (67) and four 3/8” LOW HEIGHT LOCKNUTS (65) as shown in FIGURE 4. (NOTE: Th...
Page 10 - FIGURE 5
STEP 5: FIGURE 5 1 0 • Insert two GUIDE RODS (33) through the SHROUD SUPPORT BRACKET (16) and intothe TOWER BASE (10) as shown on FIGURE5. • Slide two 3/4 X 2” WEIGHT STACK CUSH- IONS (32) down over the GUIDE RODS (33)as shown in FIGURE 5. • Using EXTREME CARE slide all twenty WEIGHT PLATES (34) dow...
Page 11 - FIGURE 6
STEP 6: FIGURE 6 11 1 5 3 3 • CAREFULLY slide three SHROUD BRACKETS (15) over all the GUIDE RODS (33) as shown in FIGURE 6. • CAREFULLY assemble the LAT/LOW BOOM (11) over all the GUIDE RODS (33) as shown in FIGURE 6. 11 0 1 1/2 1/2 1/2 1/2 1/2 1/2 2 3 4 5 6 10 20 30 40 50 60 70 80 90 100 110 120 13...
Page 12 - FIGURE 8; FIGURE 7
STEP 7: 1 2 • LOOSELY assemble the LAT/LOW BOOM (11) to the LAT/LOW FRAME (14) and the TOWER UPRIGHT (9) using seven RH CAPS (69), two 3/8 X 73mm BOLTS (57), two 3/8 X 90mm BOLTS (58), seven 3/8” SAE WASHERS (66), seven 3/8” RH WASHERS(67) and three 3/8” LOW HEIGHT LOCK NUTS (65) as shown in FIGURE ...
Page 13 - FIGURE 9
1 3 TIGHTEN! STEP 9: FIGURE 9 • Securely tighten all loose frame connections made to this point, then proceed to snap RH CAPS (69) over the RH WASHERS (67) on all tightened connections. TIGHTEN! 0 1 1/2 1/2 1/2 1/2 1/2 1/2 2 3 4 5 6 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 LUBRICATION NOTE...
Page 30 - Please refer to the LEG PRESS PARTS LIST to complete the
FIGURE 33 STEP 33: 3 0 • SECURELY assemble the STORAGE PEGS (76) to the STORAGE UPRIGHT (75) using two RH CAPS (69), two 3/8 X 25mm BOLTS (49), two 3/8” SAE WASHERS (66) and two 3/8” RH WASHERS (67) as shown in FIGURE 33. • SECURELY assemble the STORAGE UPRIGHT (75) to the TOWER BASE (10) using four...
Page 42 - PREVENTATIVE MAINTENANCE TIPS; Consult your physician before beginning any exercise program.; CLEAN; WARRANTY INFORMATION
Clean: • Upholstery with mild soap and water.• Guide rods with a cotton cloth.• Hand grips with mild soap and water.• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at (800) 351-3737 Inspect: • Cables for wear or damage and pro...