LG LSRE307ST - Manuals - manualsarea.com

Page 2 - SAFETY; BEFORE YOU BEGIN; WARNING; • The information in this manual should be followed exactly.; reengaged when the range is pushed back against the wall.; CAUTION; • Put on gloves during installation procedure.; - Failure to do so can result in bodily injury.; the cabinets If cabinet storage is to be provided.

2 Part 1 SAFETY 1 BEFORE YOU BEGIN Remove all tape and packing materials before using the range. Dispose of all plastic bags after unpacking the range. Never allow children to play with packing materials. IMPORTANT SAFETY INSTRUCTIONS Read and follow all instructions before using your oven to preven...

Page 3 - PARTS PROVIDED; NOTE; TOOLS NEEDED; PREPARE TO INSTALL THE RANGE; PARTS NOT PROVIDED; • The information in this manual; - A fire or electrical shock may result causing; • Put on gloves during installation; - Failure to do so can result in bodily injury.; • DO NOT step or sit on oven; - The range could be tipped and; ENGLISH

3 Part 1 SAFETY PARTS PROVIDED NOTE • Read all instructions contained in these installation instructions before installing range. • Remove all packing materials from the oven compartments before connecting the electricalsupply to the range. • Observe all governing codes and ordinances.• Be sure to l...

Page 4 - FIGURE 1; • Make sure that the wall covering,; • Cabinet storage space located above; - The risk of burns or fire by reaching over the

INSTALLATION DRAWINGS (LRE/LSRE Series only) NOTE SAVE FOR THE USE OF THE LOCAL ELECTRICAL INSPECTOR. CLEARANCES AND DIMENSIONS (Figure 1) To install range refer to the following Figure 1. For installation in CANADA, a Free-standing range is not to be installed closer than 15 / 32 (12mm) from any ad...

Page 6 - CONNECT RANGE CORD; ELECTRICAL CONNECTIONS

The Cord/Conduit connection plate is used for theinstallation of power cord or conduit. For power cord,install it with the connection plate as INSTALLED. Forconduit, remove the connection plate located belowthe rear of the drawer body and use the conduit hole(1 1 / 8 ”) instead of power cord hole (1...

Page 7 - FIGURE 7; -wire connection with a power supply cord; • The middle (neutral or ground) wire of a 3; - Failure to do so can result in electrical shock, severe; Install the power cord as follows:; DO NOT install the power cord without a strain relief.; Do not remove the ground strap connections.

7 Part 3 ELECTRICAL CONNECTIONS FIGURE 7 FIGURE 8 3-wire connection Assemble the strain relief to the 1 3 / 8 ” opening in Conduit connection plate Separate Strain Relief before installation 3-wire connection with a power supply cord WARNING • The middle (neutral or ground) wire of a 3 wire power co...

Page 8 - CONNECT RANGE; Install the conduit as follows:; Do not remove ground strap connections.; -wire connection with a power supply cord; • Only a 4-conductor power-supply cord kit

8 Part 3 ELECTRICAL CONNECTIONS Follow the instructions under “ CONNECT RANGE CORD ” on page 5 to correctly install the strain relief. 1. Remove the lower 3 screws from the terminal block and retain them. (Refer to Figure 9.)Remove the ground screw and retain it. 2. Remove ground strap and discard a...

Page 9 - DO NOT install the conduit without a strain relief.; Remove ground strap and discard as shown

9 Part 3 ELECTRICAL CONNECTIONS 1. Follow the instructions under “Install the conduit as follows” on page 7 to correctly install the strainrelief. DO NOT install the conduit without a strain relief. 2. Loosen the 2 lower left and right screws from the terminal block. (Refer to Figure 12.)Remove the ...

Page 10 - ANTI-TIP DEVICE INSTALLATION; Locate the bracket using the template; FINAL INSTALLATION; INSTALL THE RANGE; Optional rear filler

Replace the access cover on the range back. Toreplace the wire cover, insert double projections in thepockets located below the opening and tighten thethree screws. ANTI-TIP DEVICE INSTALLATION 1. Locate the bracket using the template An Anti-tip bracket is packaged with template. Theinstructions in...

Page 11 - Para comunicarse con LG Electronics

Printed in Mexico Para comunicarse con LG Electronics 24 horas al día, 7 días a la semana: 1-800-243-0000 (EE.UU.) O visítenos en la Web en: www.lg.com To contact LG Electronics 24 hours a day, 7 days a week: 1-800-243-0000 (U.S.A.) Or visit us on the Web at: www.lg.com