Lenovo 5354- Manuals

Chapter 1. Product overview This chapter describes the computer features, specifications, preinstalled softwareprograms, and part and connector locations. Features This section provides information about the computer features. System information The following information covers a variety of models. ...

Specifications This section lists the physical specifications for your computer. Dimensions Width: 286 mm (11.26 inches) Height: 82.5 mm (3.25 inches) Depth: 235.5 mm (9.27 inches) Weight Maximum configuration as shipped: 4.18 kg (9.22 lbs) Environment Air temperature: Operating: 10° to 35°C (50° to...

Note: The Lenovo ThinkVantage Tools program is only available on computerspreinstalled with Windows 7 from Lenovo. ThinkVantage Productivity Center: The ThinkVantage Productivity Center program guides you to a host of information and tools to help you set up,understand, maintain, and enhance your co...

Locating connectors on the rear of your computer Figure 2 shows the locations of the connectors on the rear of your computer. Someconnectors on the rear of your computer are color-coded to help you determinewhere to connect the cables on your computer. 1 Cable lock latch 6 Microphone connector 2 ac ...

Locating components To remove the computer cover, see “Removing the computer cover” on page 12. Figure 3 shows the locations of the various components in your computer. 1 Front audio and USB assembly 6 Heat sink 2 Hard disk drive 7 System board 3 System fan assembly 8 Battery 4 Optical drive 9 Memor...

Locating parts on the system board Figure 4 shows the locations of the parts on the system board. 1 Battery 8 SATA connectors (2) 2 Thermal sensor connector 9 Front USB connector 2 3 Clear CMOS (Complementary Metal Oxide Semiconductor) /Recovery jumper 10 Front audio connector 4 Serial (COM) connect...

Chapter 2. Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for yourcomputer. Handling static-sensitive devices Do not open the static-protective package containing the new part until thedefective part has been removed from the computer and yo...

Removing the computer cover Attention Do not open your computer or attempt any repair before reading and understanding the“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide , go to: h...

Removing and reinstalling the front bezel Attention Do not open your computer or attempt any repair before reading and understanding the“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Gu...

4. Go to “Completing the parts replacement” on page 24. Installing or replacing a memory module Attention Do not open your computer or attempt any repair before reading and understanding the“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To o...

4. Insert the new memory module into the appropriate memory slot. Make surethat the notch 2 of the new memory module are aligned with the slot key 1 of the memory slot. Then, press the new memory module firmly and pivot itdown until it snaps into position. Make sure that the new memory module isfirm...

8. Slide the new hard disk drive into the hard disk drive bay and pivot it downuntil it snaps into position. 9. Reconnect the power cable to the optical drive. What to do next: v To work with another piece of hardware, go to the appropriate section. v To complete the replacement, go to “Completing t...

What to do next: v To work with another piece of hardware, go to the appropriate section. v To complete the replacement, go to “Completing the parts replacement” onpage 24. Replacing the heat sink Attention Do not open your computer or attempt any repair before reading and understanding the“Importan...

4. Place the new heat sink on the system board so that the four screws are alignedwith the four corresponding mounting studs on the system board. 5. Alternate tightening each screw a small and equal amount until the heat sink issecured to the system board. Do not over-tighten the screws. What to do ...

Replacing the ac power adapter Attention Do not open your computer or attempt any repair before reading and understanding the“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide , go to...

Replacing the keyboard or mouse Attention Do not open your computer or attempt any repair before reading and understanding the“Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide , go t...

Completing the parts replacement After completing the installation or replacement for all parts, you need to reinstallthe computer cover and reconnect cables. Depending on the parts you installed orreplaced, you might need to confirm the updated information in the Setup Utilityprogram. Refer to Chap...

4. Position the computer cover on the chassis so that the rail guide on thecomputer cover engages the rail on the chassis. Then, pivot the computer coverclosed until it snaps into position. 5. If there is a computer cable lock available, lock the computer. 6. Reconnect the external cables and power ...

computers. You can order a security cable directly from Lenovo by searching for Kensington at: http://www.lenovo.com/support Password protection To deter unauthorized use of your computer, you can use the Setup Utilityprogram to set a password. When you turn on your computer, you are promptedto type...

Chapter 3. Recovery information This chapter will help you get familiar with recovery solutions provided byLenovo. This chapter explains when and how to use the following recoverymethods: v Creating and using recovery media v Performing backup and recovery operations v Using the Rescue and Recovery ...

v To create Product Recovery discs on Windows Vista, click Start → All Programs → ThinkVantage → Create Product Recovery Media . Then, follow the instructions on the screen. v To create Product Recovery discs on Windows XP, click Start → All Programs → ThinkVantage → Create Recovery Media . Then, fo...

3. Click the Restore your system from a backup icon. 4. Follow the instructions on the screen. v To perform a recovery operation using the Rescue and Recovery program onWindows Vista or Windows XP, do the following: 1. From the Windows desktop, click Start → All Programs → ThinkVantage → Rescue and ...

3. When you hear beeps or see a logo screen, release the F11 key. 4. If you set a Rescue and Recovery password, type your password whenprompted. The Rescue and Recovery workspace opens after a short delay. Note: If the Rescue and Recovery workspace fails to open, see “Solvingrecovery problems” on pa...

2. Follow the instructions on the Web site at: http://www.lenovo.com/think/support/site.wss/document.do?lndocid=MIGR-54483 3. After the recovery repair diskette is created, take out the diskette from thediskette drive and label it Recovery Repair Diskette . Then, store it in a safe place for future ...

Chapter 4. Using the Setup Utility The Setup Utility program is used to view and change the configuration settings ofyour computer, regardless of which operating system you are using. However, theoperating system settings might override any similar settings in the Setup Utilityprogram. Starting the ...

v Be significantly different from your previous passwords Set User Password After you have set a user password using the Set User Password option, the user isprompted to type a valid password each time the computer is turned on. Thecomputer cannot be used until a valid password is typed in. For more...

Exiting from the Setup Utility program After you finish viewing or changing settings, press Esc to return to the SetupUtility program main menu. You might have to press Esc several times. If youwant to save the new settings, press F10 to save and exit the Setup Utilityprogram. Otherwise, your change...

Chapter 5. Updating system programs This chapter contains information about updating POST/BIOS and how to recoverfrom a POST/BIOS update failure. Using system programs System programs are the basic layer of software built into your computer. Systemprograms include the POST, the BIOS code, and the Se...

3. When prompted to change the serial number, press N. If you want to changethe serial number, press Y when prompted, type in the serial number and pressEnter. 4. When prompted to change the machine type/model, press N. If you want tochange the machine type/model, press Y when prompted, type in the ...

Chapter 6. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If yourcomputer problem is not described here, see Chapter 7, “Getting information, help,and service,” on page 49 for additional troubleshooting resources. Basic troubleshooting The ...

Symptom Action The computer beeps multipletimes before the operatingsystem starts. Verify that no keys are stuck. Diagnostic programs Diagnostic programs are used to test hardware components of your computer andreport operating-system-controlled settings that can cause hardware failures. Thereare tw...

To run the Lenovo System Toolbox, click Start → All Programs → Lenovo Services → Lenovo System Toolbox . Follow the instructions on the screen. For additional information about running the Lenovo System Toolbox, refer to the Lenovo SystemToolbox help system. The Lenovo System Toolbox also has proble...

Running the diagnostic program from a diagnostic disc This section provides instructions on how to run the diagnostic program from adiagnostic disc that you created. To run the diagnostic program from a diagnostic disc that you created, do thefollowing: 1. Make sure the optical drive you want to use...

Chapter 7. Getting information, help, and service This chapter contains information about help, service, and technical assistance forproducts manufactured by Lenovo. Information resources You can use the information in this section to access useful resources relating toyour computing needs. Online B...

v Access troubleshooting and support information for your computer model andother supported products. v Find the service and support phone numbers for your country or region. v Find a Service Provider located near you. Help and service This section contains information about obtaining help and servi...

For a list of the Lenovo Support phone numbers for your country or region, go tohttp://www.lenovo.com/support and click Support phone list or refer to the ThinkCentre Safety and Warranty Guide that is provided with your computer. Note: Phone numbers are subject to change without notice. If the numbe...

Index A ac power adapter, replacing 22Access Help 50antivirus software 5audio line-in connector 8audio line-out connector 8audio subsystem 1 B backup and recovery operations 31basic troubleshooting 43BIOS, updating (flashing) 41, 42 C cable lock, security 25Change Supervisor Password 38changing star...

Vital Product Data . . . . . . . . . . . 99 BIOS levels . . . . . . . . . . . . . . . . 99 Updating (flashing) BIOS from a disc . . . . . . 99 Recovering from a POST/BIOS update failure . . 100 Power management . . . . . . . . . . . . 100 Automatic configuration and power interface(ACPI) BIOS . . . ...

Chapter 1. About this manual This manual contains service and reference information for ThinkCentre® computer machine types listed onthe front cover. This manual is intended only for trained Service Providers who are familiar with Lenovo®computer products. Note: Be sure to read and understand the Ch...

Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers. Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliersto be ready to support Lenovo's requirements and schedule in the EU. Product...

Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer. General safety Follow these rules to ensure general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting a...

Voltage-selection switch Some computers are equipped with a voltage-selection switch located near the power-cord connectionpoint on the computer. If your computer has a voltage-selection switch, ensure that you set the switch tomatch the voltage available at your electrical outlet. Setting the volta...

• German • Hebrew • Italian • Korean • Spanish DANGER Electrical current from power, telephone and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfigurationof this product during an electrical storm....

≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) 1 2 PERIGO 10 Hardware Maintenance Manual

• Não remova as tampas. A remoção das tampas de um produto a laser pode resultar em exposição prejudicial à radiação de laser. Não existem peças que podem ser consertadas no interior do dispositivo. • A utilização de controles ou ajustes ou a execução de procedimentos diferentes dos especificados aq...

1 2 DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenterun danger. Pour éviter tout risque de choc électrique : • Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au...

Connexion Déconnexion 1. Mettez les unités HORS TENSION. 2. Commencez par brancher tous les cordons sur les unités. 3. Branchez les câbles d'interface sur des connecteurs. 4. Branchez les cordons d'alimentation sur des prises. 5. Mettez les unités SOUS TENSION. 1. Mettez les unités HORS TENSION. 2. ...

• Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerkenund Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- undKonfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind. • Zum Installieren, Transportieren und Öff...

Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegelverwenden. Strahlungsbereich meiden. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit...

• Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale. • Non accendere assolutamente apparecchiature in presenza di incendi, perdite d'acqua o dannostrutturale. • Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima diaprire i c...

• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y losmódems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique locontrario en los procedimientos de instalación y configuración. • Conecte y desconecte los cables, como se describe...

Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta losiguiente: Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera coninstrumentos ópticos, y evite exponerse directamente al rayo láser. ≥18 kg (37 lbs) ≥32 ...

Chapter 3. General information This chapter provides general information that you can use to access useful resources relating to yourcomputing needs. Online Books folder The Online Books folder preinstalled on your computer contains the ThinkCentre User Guide , which provides information about your ...

To access the ThinkVantage Productivity Center program, click Start ® All Programs ® ThinkVantage ® Productivity Center . Lenovo Welcome The Lenovo Welcome program introduces some innovative built-in features of Lenovo to you and guides youthrough some important setup tasks to help you make the most...

Chapter 4. General checkout Attention The drives in the computer you are servicing might have been rearranged or the drive startup sequence mighthas been changed. Be extremely careful during write operations such as copying, saving, or formatting.Data or programs can be overwritten if you select an ...

4. Verify that you are using a working ac power outlet. Plug another device into the outlet or contact the power company or supplier to verify that the outlet is working correctly. 5. Check the power cord continuity. 6. Replace the ac/dc power adapter. 7. Verify that the power cord of the ac/dc powe...

Chapter 5. Diagnostics Diagnostic programs are used to test hardware components of your computer and reportoperating-system-controlled settings that can cause hardware failures. There are two programs preinstalledon your computer to help you diagnose computer problems: • Lenovo ThinkVantage Toolbox ...

PC-Doctor for Rescue and Recovery The PC-Doctor for Rescue and Recovery diagnostic program is part of the Rescue and Recovery workspaceon each Lenovo computer. Use the PC-Doctor for Rescue and Recovery program if you are unable tostart the Windows operating system. To run the PC-Doctor for Rescue an...

Note: You can insert the disc into the optical drive when you are setting the startup device sequence. However, if you insert the disc into the optical drive when you have already entered the operatingsystem, you need to restart the computer to access the diagnostic program. 3. Follow the instructio...

• ChkDigits: Contains a 2-digit check-digit value to ensure the following: – Diagnostics were run on the specified date. – Diagnostics were run on the specified computer. – The diagnostic error code is recorded correctly. • Text: Description of the error. Note: See “Diagnostic error codes” on page 4...

Chapter 6. Using the Setup Utility The Setup Utility program is used to view and change the configuration settings of your computer, regardlessof which operating system you are using. However, the operating system settings might override any similarsettings in the Setup Utility program. Starting the...

Chapter 7. Symptom-to-FRU index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first.Always begin with the Chapter 4 “General checkout” on page 33. You can use this index to help you decidewhich FRUs are needed when servicing a computer. If you are...

Diagnostic error code FRU/Action 305-000-XXX Monitor DDC test passed No action 305-250-XXX Monitor DDC self test failure 1. Run Setup to enable DDC 2. Cable 3. Monitor 4. Video card 5. System board 415-000-XXX Modem test Passed No action 415-XXX-XXX Modem error Remove the Modem and re-test the syste...

POST error message Description/Action CMOS battery failed The CMOS battery is no longer functional. Replace the battery. CMOS checksum error - defaults loaded Checksum of CMOS is incorrect. The computer loads the default configuration settings.This error might indicate that CMOS has become corruptdu...

Message/Symptom FRU/Action Program loads from the hard disk with a known-gooddiagnostics diskette in the first 3.5-inch diskette drive 1. Run setup and check startup sequence. 2. Diskette Drive 3. Diskette Drive Cable 4. System Board 5. AC/DC power adapter PXE computer cannot access programs from it...

Chapter 8. Replacing FRUs This chapter provides step-by-step instructions for replacing major FRUs. Important 1. Be sure to read and understand the Chapter 2 “Safety information” on page 3 before replacing any FRU. These precautions and guidelines will help you work safely. 2. The replacement proced...

Figure 2. Rear connector locations 1 Cable lock latch 6 Microphone connector 2 ac power adapter connector 7 Audio line-out connector 3 VGA monitor connector 8 Audio line-in connector 4 USB connectors (4) 9 Serial port (some models) 5 Ethernet connector Locating components Figure 3 “Component locatio...

Figure 3. Component locations 1 Front audio and USB assembly 6 Heat sink 2 Hard disk drive 7 System board 3 System fan assembly 8 Battery 4 Optical drive 9 Memory modules (2) 5 Microprocessor Locating parts on the system board Figure 4 “System board part locations” on page 68 shows the locations of ...

Figure 4. System board part locations 1 Battery 8 SATA connectors (2) 2 Thermal sensor connector 9 Front USB connector 2 3 Clear CMOS (Complementary Metal Oxide Semiconductor) /Recovery jumper 10 Front audio connector 4 Serial (COM) connector 11 System fan connector 5 Front panel connector 12 Intern...

1. Remove any media from the drives. Then, turn off all attached devices and the computer. 2. Disconnect all power cords from electrical outlets. 3. Disconnect the power cords, Input/Output (I/O) cables, and any other cables that are connected to the computer. 4. Remove any locking devices, such as ...

Figure 6. Removing the front bezel 3. To reinstall the front bezel, align the holes in the bottom of the front bezel with the corresponding plastic tabs on the chassis. Then, pivot the front bezel inward until it snaps into position. Figure 7. Reinstalling the front bezel 4. Go to “Completing the pa...

To install or replace a memory module, do the following: 1. Remove the computer cover. See “Removing the computer cover” on page 68. 2. Locate the memory slots on the system board. See “Locating parts on the system board” on page 67. 3. If you are replacing a memory module, open the retaining clips ...

Replacing the battery Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information”in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide , go to:http://w...

7. Use the Setup Utility program to set the date, time, and any passwords. See Chapter 6 “Using the Setup Utility” on page 41. Replacing the hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information”in the ThinkCentre...

Figure 13. Installing the hard disk drive into the bracket 7. Connect the signal cable and the power cable to the rear of the new hard disk drive. 8. Slide the new hard disk drive into the hard disk drive bay and pivot it down until it snaps into position. Figure 14. Installing the hard disk drive 9...

1. Remove the computer cover. See “Removing the computer cover” on page 68. 2. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 69. 3. Disconnect the signal cable and the power cable from the rear of the optical drive. 4. Press the blue release button 1 and slide the o...

Figure 17. Installing the optical drive 7. Connect the signal cable and the power cable to the rear of the new optical drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 84. ...

Figure 18. Removing the heat sink 4. Place the new heat sink on the system board so that the four screws are aligned with the four corresponding mounting studs on the system board. 5. Alternate tightening each screw a small and equal amount until the heat sink is secured to the system board. Do not ...

Figure 19. Removing the system fan assembly 5. Install the two new short rubber mounts to the new system fan assembly. Note: The new system fan assembly comes together with four new rubber mounts: two short rubber mounts and two long rubber mounts. Figure 20. Installing the short rubber mounts 6. In...

Figure 21. Installing the system fan assembly 8. Connect the cable of the new system fan assembly to the system fan connector on the system board. 9. Reinstall the hard disk drive if you have removed it. What to do next: • To work with another piece of hardware, go to the appropriate section. • To c...

Figure 22. Accessing the microprocessor 6. Lift the microprocessor straight up and out of the microprocessor socket. Notes: a. Your microprocessor and socket might look different from the one illustrated. b. Note the orientation of the microprocessor in the socket. You can either look for the small ...

Figure 23. Removing the microprocessor 7. Make sure that the small handle is in the raised position and the microprocessor retainer is open. 8. Remove the protective cover 2 that protects the gold contacts of the new microprocessor 1 . 9. Hold the new microprocessor and align the notches on it with ...

Replacing the system board Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information”in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide , go to:htt...

3. Insert the tabs 1 of the socket cover into the hinged side of the socket, and then press the other side of the socket cover downward until the tabs 2 snap into position. Figure 24. Tabs on the microprocessor socket cover (bottom view) Figure 25. Installing the microprocessor socket cover Replacin...

Figure 26. Connecting the ac power adapter What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 84. Completing the parts replacement This section provides instructions on how to compl...

Chapter 9. FRU lists This chapter lists the FRU information. Attention: Be sure to read and understand the Chapter 2 “Safety information” on page 3 and Appendix A “Notices” on page 101 before replacing any FRUs. Note: In the following tables, a CRU is identified as "1", "2", or "...

Item # 3425 FRUs FRU # CRU 1 Hard disk drive, SATA 500GB 7200RPM / 3Gb / 16M (models) 45K0410 1 3 Optical drive, DVD-ROM Drive - 16x/48x - SATA (models A1J A3J A5J A8J B1J) 41N3325 1 3 Optical drive, DVD-ROM Drive - 16x/48x - SATA (models A1J A3J A5J A8J B1J) 71Y5543 1 3 Optical drive, DVD Recordabl...

Chapter 10. Additional service information This chapter provides additional information that the service representative might find helpful. Security features Security features in this section include the following: • Passwords • Vital Product Data Hardware controlled passwords Use the Setup Utility ...

2. Make sure the computer is turned on and insert the disc into the optical drive. The update begins. Note: You can insert the disc into the optical drive when you are setting the startup device sequence. However, if you insert the disc into the optical drive when you have already entered the operat...