La Crosse Technology WT-5721 - Manuals

Page 2 - Program Mode

2 TABLE OF CONTENTS Topic Page Inventory of Contents/ Additional Equipment 3 About WWVB 3 Quick Set-Up Guide 4 Detailed Set-Up Guide Battery Installation 5 Program Mode Programming Sequence 6 Function Buttons 6 Time Zone Setting 6 DST (Daylight Saving Time) Setting 7 Adjustable Snooze 7 Time Setting...

Page 3 - Operation of these features is in section III.

3 INVENTORY OF CONTENTS 1) WT-5721 Alarm Clock 2) TX6U Remote temperature sensor 3) AC adapter/transformer 4) Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) 1) Two fresh 1.5V AA batteries (optional for alarm clock) 2) Two fresh 1.5V AA batteries (for remote sensor) FEATURE...

Page 4 - outdoor remote

4 QUICK SET-UP GUIDE Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor station and outdoor remote 3 to 5 apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the outdoor remote first then into the indoor station. (Al...

Page 5 - batteries. The batteries will fit tightly (to avoid; ALARM; Remove the battery cover.

5 Battery Cover DETAILED SET-UP GUIDE II. BATTERY INSTALLATION A. REMOTE TEMPERATURE SENSOR 1. Remove the battery cover. Observing the correct polarity, install 2 AA batteries. The batteries will fit tightly (to avoid start-up problems make sure that they do not spring free during installation). 2. ...

Page 6 - DISPL; TIME ZONE SETTING; SET”

6 III. PROGRAM MODE To enter the Program Mode hold down the “SET” button for 1 second, until the time zone (“-5” default) flashes in the lower left. The Program Mode Guide is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to prog...

Page 8 - SETTING; C instead of

8 9. Press and release the “ SET” button to confirm the calendar settings, and to advance to select either 12 or 24-hour time display. H. 12/24-HOUR SETTING Note: Setting to the 24 hour mode (also known as Military Time) will also change the temperature to display in ° C instead of ° F. 1. Hold down...

Page 10 - Light intensity

10 6. The projector case can be rotated 180 ° to further help orient the projected display. 7. The intensity of the projection can be adjusted to three different settings as well as turned “off” by pressing the light Intensity button. When turned off, the projection will only come on when a button i...

Page 11 - SETTING THE ALARM

11 G. TIME ALARM The projection alarm has two separate alarms for time, “ALM1” and “ALM2”. The alarms have a different sound; ALM1 increases in volume after 25 seconds, and again after 50 seconds. ALM2 is a constant volume. The total duration is 96 seconds for each alarm. 1. SETTING THE ALARM a. Pre...

Page 12 - MOUNTING WITH SCREWS; Where marked, start the screw holes into the mounting surface.; MOUNTING WITH ADHESIVE TAPE; Do not submerge in water.

12 V. MOUNTING THE REMOTE TEMPERATURE SENSOR A. The Remote Temperature Sensor can be mounted in two ways: 1) with the use of screws, or 2) using the adhesive tape. B. MOUNTING WITH SCREWS 1. Remove the mounting bracket from the Remote Temperature Sensor. The bracket should snap off easily. 2. Place ...

Page 13 - TROUBLESHOOTING

13 TROUBLESHOOTING Problem: The Projection is faint Solution: 1) Change intensity setting 2) Use AC adapter 3) Darken surroundings 4) Use fresh batteries (if AC is not used) Problem: The LCD is faint. Solution: 1) Replace the batteries. Problem: “OFL” appears in the indoor temperature LCD. Solution:...

Page 14 - SPECIFICATIONS FOR WT-5721

14 SPECIFICATIONS FOR WT-5721 Temperature: Measuring range: 32 ° F to 122 ° F with 0.2 ° F resolution (indoor) -21.8 ° F to 140 ° F with 0.2 ° F resolution (outdoor) (0 ° C to 50 ° C with 0.1 ° C resolution) Checking intervals: Every 10 seconds indoor, 3 times in 10 minutes for remote temperature. P...

Page 15 - WARRANTY INFORMATION

15 WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to th...