La Crosse Technology WS-7391U - Manuals

Page 2 - Detailed Set-Up Guide; Program Mode; Features

2 TABLE OF CONTENTS Topic Page Inventory of Contents/Additional Equipment 3 About WWVB 4 Quick Set-Up Guide 5-6 Detailed Set-Up Guide Battery Installation 7-8 Program Mode Time and Date 8-9 Function Keys 9 12/24 hour Time Setting 9 Time Setting 10 Time Zone Setting 10-11 Daylight Saving Time (DST) S...

Page 4 - ABOUT WWVB

4 ABOUT WWVB The NIST (National Institute of Standards and Technology—Time and Frequency Division) radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away throu...

Page 5 - sensor; first then into the indoor weather station.

5 QUICK SET-UP GUIDE Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor weather station and remote thermo/hygro sensor 3 to 5 apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote thermo/hygro sensor first t...

Page 7 - Remote Thermo/hygro Sensor; Press the arrow and slide the battery cover off.; Indoor Weather Station; Replace the battery cover.

7 DETAILED SET-UP GUIDE BATTERY INSTALLATION A. Remote Thermo/hygro Sensor 1. Pull the cylindrical rain cover off the remote thermo/hygro sensor. 2. Remove the battery cover (located on the backside of the remote thermo/hygro sensor, above the mounting post and bracket). 3. Press the arrow and slide...

Page 8 - ) Automatically via WWVB reception (only need to set the

8 is achieved easiest at night), it will display the correct time (factory setting is Eastern time zone). PROGRAM MODE Programming Note: If 20 seconds is allowed to pass during programming modes, the unit will confirm/set the last information entered—the display will stop flashing and return to norm...

Page 10 - III. Time Zone Setting

10 II. Time Setting Note: This is only necessary if you do not wish to wait for the WWVB reception. All manual set data will be over-ridden by the reception of the WWVB signal based on the time zone selected. 1. Press and hold the “SET” button (on the back of the clock) for 2 seconds or until “12h” ...

Page 15 - C and

15 then the weather has not changed or the change has been slow and gradual. If this happens on a regular basis, it may be necessary to adjust the weather forecast sensitivity. 2. Weather Tendency Arrows Other possible displays in the TENDENCY LCD are 2 weather tendency arrows, one that points up an...

Page 16 - III. Outdoor Temperature and Humidity; Adding; Outdoor and Resetting); This will reset both the indoor and outdoor records, it is not

16 III. Outdoor Temperature and Humidity The outdoor temperature and humidity is viewed in the OUTDOOR LCD. When there is more than one remote sensor unit in operation a “boxed” number will appear to the right of the temperature. This indicates which remote sensor unit (1, 2, or 3) is currently disp...

Page 18 - VII. Viewing and Operating with Multiple Remote Sensors; “CHANNEL”

18 VII. Viewing and Operating with Multiple Remote Sensors 1. To view the temperature of a different remote sensor press and release the “CHANNEL” button. A shift from one “boxed” number to the next should be observed in the OUTDOOR LCD. 2. The minimum and maximum temperature of the additional remot...

Page 19 - Remove the mounting bracket/receptor from the

19 VIII. Mounting Note: Before permanently mounting ensure that the indoor weather station is able to receive WWVB signals from the desired location. Also, extreme and sudden changes in temperature will decrease the accuracy of the indoor weather station. Changes in elevation will result with inaccu...

Page 20 - Mounting With Adhesive Tape

20 5. Remove screws from the mounting surface. 6. Align the mounting bracket with the started screw holes. 7. Screw mounting bracket onto the mounting surface. The screws should be flush with the bracket. 8. Fit the mounting post (on the back of the remote thermo/hygro sensor) into the receptor of t...

Page 21 - The Indoor Weather Station; The WS-7391U is a wall mount only indoor weather

21 2. The Indoor Weather Station 1. The WS-7391U is a wall mount only indoor weather station. To mount the display on your wall: 2. Fix a screw (not included) into the desired wall, leaving approximately 3/16 of an inch (5mm) extended from the wall. 3. Place the indoor weather station onto the screw...

Page 23 - Do not submerge in water.; Temperature measuring range:

23 Maintenance and Care Instructions • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings. • Do not submerge in water. • Immedi...

Page 26 - La Crosse Technology

26 This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information...