La Crosse Technology WS-7044U - Manuals

Page 2 - Battery installation

2 TABLE OF CONTENTS Topic Page Inventory of Contents/Additional Equipment 3 Quick set-up guide 3 Battery installation 4-6 Time 7-8 Features: 9-15 Indoor temperature 10 Weather Forecast icons & tendency arrows 10-13 Outdoor temperature with Minimum & Maximum 13-15 Mounting 15-19 Troubleshooti...

Page 4 - Replace the battery cover.

4 DETAILED SET-UP GUIDE I. BATTERY INSTALLATION A. REMOTE TEMPERATURE SENSOR 1. Remove the battery cover. Place your thumb over the two air-vent slots on the face of the Remote Temperature Sensor, push down gently, slide battery cover down and off. 2. Observing the correct polarity, install 2 AAA ba...

Page 7 - Press the

7 II. TIME A. THE TIME DISPLAY The time is displayed vertically (with the hour displayed above the minutes) rather than in the conventional horizontal format. The hour and minute displays are separated by a flashing dot, which indicates the seconds. The time is only displayed in the 12h mode, there ...

Page 9 - option to read the temperature in

9 FEATURES Note: All temperatures are read in ° F, there is no option to read the temperature in ° C. HOUR LCD MINUTE LCD INDOOR LCD FORECAST LCD OUTDOOR LCD MINIMUM/MAXIMUM BUTTON

Page 12 - B. WEATHER TENDENCY ARROWS

12 change in order from: “sunny” to “sun with clouds” to “clouds with rain,” or the reverse. It will not change from “sunny” directly to “rainy,” although it is possible for the change to occur quickly. If the symbols do not change then the weather has not changed, or the change has been too slow an...

Page 16 - THE REMOTE TEMPERATURE SENSOR; with the use of screws, or; MOUNTING WITH SCREWS; Where marked, start the screw holes

16 desired location, and wait approximately 10 minutes before permanently mounting to ensure that there is proper reception. The Weather Temperature Station should display a temperature in the OUTDOOR LCD within 3 minutes of setting-up. I. THE REMOTE TEMPERATURE SENSOR The Remote Temperature Sensor ...

Page 17 - into the mounting surface.; MOUNTING WITH ADHESIVE TAPE

17 into the mounting surface. 4. Screw mounting bracket onto the mounting surface. Ensure that the screws are flush with the bracket. 5. Snap the Remote Temperature Sensor onto the mounted bracket. B. MOUNTING WITH ADHESIVE TAPE 1. With a nonabrasive solution, clean and dry the back of the mounting ...

Page 18 - No outdoor temperature is displayed.

18 II. THE WEATHER STATION The Weather Station can be mounted on the wall with the use of a wall hanging screw (not included). A. WALL MOUNTING 1. Place a screw (not included) into an appropriate wall, leaving approximately 3/16 of an inch (5mm) extended from the wall. 2. Place the Weather Station o...

Page 19 - Replace

19 2) Place sensor closer to station. 3) Be sure there are no obstructing objects. 4) Be sure all batteries are fresh. Problem: The LCD screens are faint/dim. Solution: Replace batteries. Note: For problems not solved, please contact La Crosse Technology.

Page 20 - Do not submerge in water.

20 MAINTENANCE AND CARE INSTRUCTIONS • Extreme and sudden temperature changes, vibration, and shock should be avoided to prevent damage to the units. • Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings. • Do not submerge ...

Page 21 - Temperature checking intervals; times every 10 minutes.

21 SPECIFICATIONS Temperature measuring range Indoor: 32 ° F to 104 ° F with 0.2 ° F resolution: (0 ° C to 40 ° C with 0.1 ° C resolution). “OFL” displayed if outside this range. Outdoor: -21.9 ° F to 157.9 ° F with 0.2 ° F resolution: (-29.9 ° C to 69.9 ° C with 0.1 ° C resolution). “OFL” displayed...

Page 22 - Power Source

22 Power Source Weather Station: 2 x AAA, 1.5V (IEC LR3) Sensor: 2 x AAA, 1.5V (IEC LR3) Dimensions (L x W x H) Weather Station: 2.95 x 0.83 x 10in. (75 x 21 x 255mm) Sensor: 2.32 x 0.83 x 2.56in. (59 x 21 x 65mm) WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on t...