KTI Networks KS-801 - Manuals

Page 5 - Table of Contents

-5- Table of Contents 1. Introduction ......................................................... 6 1.1 Features ............................................................................... 71.2 Specifications ....................................................................... 9 2. Installing t...

Page 10 - Installing the Switch; country of operation.

-10- 2. Installing the Switch The switch is designed to operate in workgroup environments without a complicated configuration procedure. It also features an auto-select 100- 240V, 50/60Hz power supply unit, which works in most countries around the world. Before connecting the supplied power cord int...

Page 12 - Mounting the Switches; The switches can be placed on a desktop as a stand-alone unit. Allow

-12- 2.3 Mounting the Switches The switches can be placed on a desktop as a stand-alone unit. Allow enough ventilation space between the switch and the objects around it. Desktop Mounting For mounting the switch into a 19-inch rack, a pair of mounting brackets is included in the pack. Install Rack M...

Page 13 - Making Network Connections; Network Switched Ports; The switch comes with nine Fast Ethernet switched ports and Port #9; Standard

-13- 3. Making Network Connections 3.1 Network Switched Ports The following figure illustrates the switched ports provided on the switch. The switch comes with nine Fast Ethernet switched ports and Port #9 provides two connection types, one is 10/100BASE-TX RJ-45 connector and the other is 100BASE-F...

Page 14 - 10/100BASE-TX Fast Ethernet Switched Ports; Crossover SW; Crossover SW

-14- 10/100BASE-TX Fast Ethernet Switched Ports Each switched port supports one connection to a LAN segments. Each segment is an independent shared network in one collision-domain. The connection can be to either a 10BASE-T or a 100BASE-TX device. MDI-X and MDI RJ-45 Connectors MDI-X jack is lab...

Page 17 - Fast Ethernet Fiber Slot; available for selection:; Module; Switched port #9 supports two types of connections. One type is UTP

-17- 3.3 Fast Ethernet Fiber Slot The switch provides one fast Ethernet fiber slot. It can accommodate one optional fiber module for your fiber connection. Depending on the fiber interface and the types of fiber cables, the following fiber modules are available for selection: Module Connector type F...

Page 20 - Making Trunk Connections; composes one trunk. Two switch units can be cascaded through one; Configuration; Refer to the software operation manuals in the supplied CD-ROM for

-20- 3.4 Making Trunk Connections Two switch units can be cascaded together through any regular switched data port on each unit when a port expansion is required. However, the transfer bandwidth between the two cascaded ports is limited to 200Mbps full duplex. To increase the bandwidth for the conne...

Page 24 - Performing Network Management; Management Support; by using the following methods:

-24- 5. Performing Network Management 5.1 Management Support The switch is featured with management functions and can be managed by using the following methods: _ Direct console connection over an RS232 cable _ Web browser software from Internet or Intranet over TCP/IP network _ Telnet software over...

Page 25 - Management objects; Port Statistics

-25- 5.2 Management objects The following table lists the management objects supported by the system: LoginPort Status - Port link status - Port control status - Port speed status - Port duplex status - Port flow control status Port Statistics - Send good, bad, abort packet counts - Receive good, ba...

Page 26 - Setting IP Address; admin; Console Management; Factory default settings of the Console port

-26- 5.3 Setting IP Address Before performing any management operation over network, the most important thing is to learn the detailed information about the TCP/IP network where the managed unit is located. The information includes the network address, subnet mask, and IP of the default router. The ...

Page 27 - from a PC COM port. The pin assignments of the connection are:; Switch DTE console port; The console port does not support modem connection.; Telnet Management; Use Telnet software to perform the management operation. The most

-27- Use the supplied RS232 cable to make the console connection directly from a PC COM port. The pin assignments of the connection are: Switch DTE console port 9-pin PC COM port Pin 2 RXD -------------------------------- 3 3 TXD -------------------------------- 2 4 DTR -----------------------------...