KitchenAid KMHS120EBS - Manuals

5 6. Using diagonal wire cutting pliers, gently snip out the rectangular damper vent covers at the perforations. 7. Reattach blower motor to back of microwave oven with 2 screws removed in Step 3. 8. Reattach damper plate. Make sure damper plate tabs are inserted into the slots in the top of the mic...

6 Locate Wall Stud(s) NOTE: If no wall studs exist within the cabinet opening, do not install the microwave oven.See illustrations in “Possible Wall Stud Configurations.” 1. Using a stud finder, locate the edges of the wall stud(s) within the opening. 2. Mark the center of each stud, and draw a plum...

7 Mark Rear Wall The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of 1 lag screw, preferably 2. 1. Using measuring tape, find and clearly mark the vertical centerline of the opening. 2. Align the center markers on the wall template to the centerline on ...

8 Attach Mounting Plate to Wall NOTE: Secure the mounting plate to the wall at both end holes drilled into the wall studs and/or drywall using either 3/16-24 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag screws.Refer to illustrations in “Possible Wall Stud Configurations” in “Locate ...

9 5. Cut the 1 1 / 2 " (3.8 cm) diameter hole at the circular shaded area “G” on the template. This hole is for the power supply cord. NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole as shown. 6. Drill 3/8" (10 mm) holes at points “D...

10 6. Push microwave oven against mounting plate and hold in place. NOTE: If microwave oven does not need to be adjusted, skip steps 7-9. 7. If adjustment is required, rotate microwave oven downward. Using 2 or more people, lift microwave oven off of mounting plate, and set aside on a covered surfac...

11 VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: ■ Vent materials needed for installation are not provided with microwave hood combination. ■ We do not recommend using a flexible metal vent. ■ To avoid possible product...

Recommended Vent Length A 3 1 / 4 " x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used.The total length of the vent system including straight vent, elbow(s), transitions and wall or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of ve...

5 6. Using diagonal wire cutting pliers, gently snip out the rectangular damper vent covers at the perforations. 7. Reattach blower motor to back of microwave oven with 2 screws removed in Step 3. 8. Reattach damper plate. Make sure damper plate tabs are inserted into the slots in the top of the mic...

6 Locate Wall Stud(s) NOTE: If no wall studs exist within the cabinet opening, do not install the microwave oven.See illustrations in “Possible Wall Stud Configurations.” 1. Using a stud finder, locate the edges of the wall stud(s) within the opening. 2. Mark the center of each stud, and draw a plum...

7 Mark Rear Wall The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of 1 lag screw, preferably 2. 1. Using measuring tape, find and clearly mark the vertical centerline of the opening. 2. Align the center markers on the wall template to the centerline on ...

8 Attach Mounting Plate to Wall NOTE: Secure the mounting plate to the wall at both end holes drilled into the wall studs and/or drywall using either 3/16-24 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag screws.Refer to illustrations in “Possible Wall Stud Configurations” in “Locate ...

9 5. Cut the 1 1 / 2 " (3.8 cm) diameter hole at the circular shaded area “G” on the template. This hole is for the power supply cord. NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole as shown. 6. Drill 3/8" (10 mm) holes at points “D...

10 6. Push microwave oven against mounting plate and hold in place. NOTE: If microwave oven does not need to be adjusted, skip steps 7-9. 7. If adjustment is required, rotate microwave oven downward. Using 2 or more people, lift microwave oven off of mounting plate, and set aside on a covered surfac...

11 VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: ■ Vent materials needed for installation are not provided with microwave hood combination. ■ We do not recommend using a flexible metal vent. ■ To avoid possible product...

Recommended Vent Length A 3 1 / 4 " x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used.The total length of the vent system including straight vent, elbow(s), transitions and wall or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of ve...