Kicker KX200.4 - Manuals - manualsarea.com

Page 2 - Features

Features KX100.2 & KX200.4 Technical Manual Version 2.0 Page 2 Radically Advanced Chassis with removable shroud and improved heatsink technology. The heatsinks provide the amplifier with longer runtime, improved reliability and performance. The height has been decreased for moreversatile install...

Page 3 - Specifications

Custom tooled gold plated connectors Assure maximum power transfer and damping. SAMS ( S tereo A nd M ono S imultaneously) Amplifier will operate into a bridged mono load and a stereo load at the same time. This type of system is great if the consumer is just starting out, or on a tight budget. Thre...

Page 4 - Mounting Instructions; Remove; Remove

When selecting a location to mount your Kicker amplifier be sure it is structurally sound and thatthere are no items behind the area that could bedamaged by the screws. Check for wiring, brakelines, fuel lines, gas tanks, etc. All amplifiers generate heat under normal opera- tion. Be sure to choose ...

Page 5 - WA; Speaker; Inputs; KX

SOURCE UNIT WA R NING-Use Only On e... Never Both At Th e Same T ime!!! Speaker Outputs RCA Outputs LEFT + LEFT - RIGHT - RIGHT + High-Level Inputs KX100.2 & KX200.4 Technical Manual Version 2.0 Page 5 KX 100 .2 Wiring Wiring Instructions

Page 7 - Wiring Instructions; RCA Dummy Plugs

Wiring Instructions SOURCE UNIT Speaker Outputs RCA Dummy Plugs LEFT + LEFT + LEFT - RIGHT - RIGHT + AMP 1 AMP 2 High-Level Inputs LEFT - RIGHT - RIGHT + When using both sets of High L ev el inputs , the supplied RC A dumm y plugs must b e inserted into the AMP 2 inputs in or der for the fa der to w...

Page 8 - GROUND; REMOTE; BATTERY; Charging System; Ampli; Additional; Chassis; Source

Wiring cont. The use of twisted pair interconnects is recommended for all installations to minimize noise. When routing these cables through the automobile, try to keep them away from factory wiring harnesses and other power wiring. Ifyou need to cross any of this wiring do so at a 90 degree angle t...

Page 9 - Adjusting Amplifier Controls; CROSSOVER SWITCHES; Fuse Ratings

Adjusting Amplifier Controls On your Kicker amplifier there are rotary controls and switches on the end panel. These controls ensure the relia- bility and performance of the amplifier, so they need to be set correctly. If you are using a KX150.4 you will havetwo sets of rotary controls and switches....

Page 10 - Crossover Control; Bass Boost; Adjusting Amplifier Controls cont.

Crossover Control Where you set the crossover is very subjective and can be fine tuned to match your listening preference or speaker requirement. If the amplifier is driving small speakers (crossover set to HI PASS) this will eliminate the lowfrequencies from damaging the high frequency speaker. If ...

Page 11 - Sy

GR OUND REMO TE TURN-ON BA T TER Y +12V FUSE RIGHT SPEAKER(S) LEFT SPEAKER(S) + _ + _ 18" or less 2 Ω Min. 2 Ω Min. SIGNAL IN When the amplifier is driving s peak er s that do not r equir e a cr osso ve r , the cr osso ve r switch ma y b e set to the OFF posit ion. This will allo w the speak er ...

Page 18 - Power Wire Chart; Minimum Gauge wire; Power Cable Calculation

(Total RMS power output into 4 W W ) x 2 = (Total input wattage [Watts]) (Total input wattage) = (Maximum input current [Amps]) (Supply Voltage) Example: Amplifier with a rating of 100 watts per channel into 4 W W 200 x 2 = 400 Watts (Total input power) 400 Watts / 12.5 Volts = 32 amps (Total maximu...