Kicker KS6.2 - Manuals - manualsarea.com

Page 2 - ALWAYS KEEP YOUR RECEIPT!

2 Introduction KS-Series System Components Owner’s Manual Models: KS65.2 / KS6.2 / KS5.2 KS-Series System Components Attention: Please record your purchase information in the area below. We recommend attaching the original sales receipt to this manual for future reference. If you require service on ...

Page 3 - tures; Features

3 F e a tures Features CIMP ™ (Curvilinear Injection-Molded Polypropylene Woofer Cones) is a high performance composite, which remains rigid, minimizes cone flex and lowers harmonic distortion. The CIMP ™ consists of a one-piece, injection-molded polypropylene material that moves as apiston, exhibit...

Page 4 - Performance

4 Specifica tions Performance Model: KS5.2 KS6.2 KS65.2 Speaker Design Rated Impedance, ohm DC Resistance, ohm Sensitivity [SPLo], dB @ 1W, 1m Power Range, Watts RMS Peak Power Handling, Watts Effective Frequency Range, Hz Top-Mount Depth, in (cm) Bottom-Mount Depth, in (cm) Mounting Hole Diameter, ...

Page 5 - Installation; Mounting; we recommend using genuine Kicker Accessories and Wiring.

Installa tion 5 Installation KS-Series System Components Your Kicker KS-Series System Component drivers are specifically designed for mounting in free-air applications. The speakers do not require a sealed enclosure for optimum performance. It is important to isolate the sound coming off the front o...

Page 6 - Figure 1 Figure 2; Grill Mounting Ring; Installa

Installation Push Grill into place andsnap onto Grill Mounting Ring Figure 1 Figure 2 To Crossover Stagger Holes For Wiring & Use Grommets (When Factory Holes and Grommets are not Available) (Optional) Grill Mounting Ring Door Panel Kick Panel If custom door mounting locations for the KS-Series ...

Page 7 - Door Body; Tweeter Mounting

Installation Door Body Tweeter Mounting Nut 2" Hole Door Panel Clearance Hole 2.5" Figure 3 (Flush Mount) Tweeter Mounting The tweeter can be mounted one of four ways: flush, surface, angled and coaxial mounting. For flush mounting applications, please refer to the illustration in Figure 3. ...

Page 8 - Tweeter Mounting continued; Figure 4

8 Installa tion Installation KS-Series System Components Tweeter Mounting continued The tweeter can be mounted in the center of the midrange. This creates a high quality coaxial speaker. Remove the tweeter face plate by screwing it off and install the supplied smaller face plate. Then install the tw...

Page 9 - Wiring Options; Tweeter; SOURCE UNIT or AMPLIFIER

Wiring Options Installa tion 9 There are three sets of wires supplied with the Kicker KS-Series System Components. One set has two different size female connectors .205” (5.2 mm) and .110” (2.8 mm) and is designed to plug on to the terminal of the midrange. The other end of this wiregoes to the midr...

Page 10 - Wiring two KS-Series System Components to a single channel; Figure 6

Installa tion 10 KS-Series System Components All specifications and performance figures are subject to change. Please visit kicker.com for the most current information. Wiring two KS-Series System Components to a single channel Modern high performance system components have a lower DC Resistance tha...

Page 11 - WHAT TO DO IF YOU NEED WARRANTY OR SERVICE; Please use common sense when controlling volume!; Warran

Acoustics LIMITED WARRANTY WHAT IS NOT COVERED? Kicker warrants this product to be free from defects in material and workmanship under normal use for a period of THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for ONE (1) ...