Keys Fitness 502t - Manuals

Assembly The HEALTH TRAINER 502t treadmill will require assembly before operating. After opening the box,remove any packing material from the treadmill. Do not throw away any packing materials until the unit is working properly. Place the base on a clean, level surface. Make sure the electrical cord...

Assembly Assembly requires the included allen wrench and your own phillips screwdriver. Do not plug in the power cord until all assembly step are completed. 1. With the treadmill deck in the down position, leave the unit on the original packing material to assemble allparts.Refer to figure 1. 2. Con...

Assembly 7 Figure 4: Left and Right Upright Installation Figure 5: Upright Crossbar Assembly Figure 6: Hardware Installation 3. Install Left Upright and Right Upright to tread-mill base frame. Refer to Figure 4.Note: Make sure that the Wire Harness is notpinched. Do not install hardware until instru...

Assembly 8 8. Connect the Console Harness andRemote Speed Harness together as shown inFigure 7. Connectors snap together asshown in Figure 8. 9. Connect Ground Wire to grounding screwlocated on the side of the Upright Assemblyusing Screw ST4.2*13 (Qty. 1) as shown inFigure 7. CONSOLE GROUND WIRE SCR...

Assembly 9 10. Make sure all wires and harnesses areinside console housing and attach the consoleback cover to the Left and Right Uprightmounting brackets using Screws ST4.2*16(Qty. 6) as shown in Figure 9. 11. Tighten all hardware (previously installed)and insert Power Cable into AC connection onre...

Warm Up Exercises TOE TOUCH STRETCH Stand bending your knees slightly and slowly bend forward from your hips.Allow your back and shoulders to relax as you reach down toward your toesas far as possible. Hold for 15 counts, then relax. This will stretch your ham-strings, back of knees, and back. HAMST...

Moving Instructions CAUTION! TO AVOID THE RISK OF INJURY, NEVER ATTEMPT TO MOVE THE TREADMILL WHILEIT IS IN THE UNFOLDED OPERATING POSITION. TO REDUCE THE POSSIBILITY OF INJURYWHILE LIFTING, BEND YOUR LEGS AND KEEP YOUR BACK STRAIGHT. AS YOU RAISE THETREADMILL, LIFT USING YOUR LEGS, NOT YOUR BACK. I...

Power Requirements I M P R O P E R C O N N E C T I O N O F T H E E Q U I P M E N T G R O U N D I N G C O N N E C TO R C A N R E S U LT I N A R I S K O F A N E L E C T R I C S H O C K . C H E C K W I T H A Q U A L I F I E D E L E C T R I C I A N O RS E RV I C E M A N I F Y O U A R E I N D O U B T A S...

Console Panel Functions There are four display windows on the control panel to provide feedback information. TIME WINDOW TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds) INTERVAL TIME: Indicates countdown in seconds to the next interval starting a...

Program and Operation QUICK START / MANUAL MODE 1. Plug into a surge protector outlet. Attach the Red Safety Key on to the treadmill console. 2. Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.3. Press POWER button. There will be an eight (8) second delay after press...

Program Profiles 16 The Fat Burn Program is designed to vary the treadmillelevation, while maintaining aconstant walking belt speed. The Cardio Program is designed to vary the treadmillSpeed, while maintaining a con-stant Elevation. The Warm Up Program is designed to gradually increase the treadmill...

Belt Adjustment WARNING! Do not over-tighten rollers! This will cause prema-ture roller bearing failure! Belt adjustment and tension performs two functions: adjustment fortension and centering. Your new treadmill comes pre-adjusted fromthe factory for tension and centering. Please follow the procedu...

Change Miles per hour to Kilometers per hour Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). Alltreadmills are calibrated at the factory for British Units (miles per hour). To change the display to read in kilo-meters, follow the steps desc...

Maintenance Instructions WARNING! Before performing any maintenance to your treadmill, always unplug the power cord from the surge protector. CLEANING Routine cleaning of your HT502t Fitness treadmill will extend the life of your treadmill. WARNING! To pre- vent electrical shock, be sure the power t...

Troubleshooting Guide Treadmill will not start . 1. Is the Safety Key inserted into the treadmill Console? 2. Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirement...

Error Messages Treadmill Error Messages . Your treadmill is equipped with a software package that enables error messages to be displayed when there isa problem. The following error codes will be displayed in the console display windows. Safety Interlock Error Messages SI 1 - Safety key missing, repl...

Calibration Sequence Do not attempt to calibrate the treadmill unless an Error Code is present. See Error Messages (page 21). Our treadmill is equipped with a software package that will perform a calibration sequence unique to yourspecific model number.Please perform the following steps to calibrate...

Parts List REF# KEYS PART# DESCRIPTION QTY. 1 423-00001 UPRIGHT CROSSBAR 1 2 423-00002 LEFT UPRIGHT 1 3 423-00003 RIGHT UPRIGHT 1 4 423-00004 BASE TUBE 1 5 423-00005 DECK FRAME 1 6 423-00006 MOTOR FRAME 1 7 404-00001 WALK BELT 430*2700*1.6 1 8 403-00001 WALK BOARD 1162*610*18 1 9 404-00002 POLY V-BE...

Warranty Information HT502t Treadmill designed and distributed by KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT. This Limited Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP(“...