Jonsered GT2125L - Manuals

English – 7 SAFETY INSTRUCTIONS 6. Cutting equipment The section describes how through correct maintenance andthrough using the right type of cutting equipment you can:• Obtain maximum clearing capacity.• Increase the service life of the cutting equipment. Two basic rules: 1)Only use the cutting and...

8 – English SAFETY INSTRUCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks ornaked flames. For example, electric machines, electricmotors, electrical switches/power switches, he...

English – 9 ! General working instructions SAFETY INSTRUCTIONS Basic working techniques • Always drop to idling speed after each working operation. Longer periods running at full throttle without loading theengine (that is without resistance, which the engine feelsfrom the cutting equipment when tri...

English – 11 WHAT IS WHAT? What is what on the trimmer? 1. Trimmer head 2. Grease filler cap 3. Angle gear 4. Spray guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13. Choke 14. Air purge 15. Air filter cover 16...

12 – English ASSEMBLY Assembling the loop handlebar(GT2125L) Assembly of the trimmer head It is extremely importantthat the disc drive’s/supportflange’s guide engagescorrectly in the cuttingequipment’s centre holewhen assembling the cuttingequipment. Cuttingequipment assembledincorrectly can result ...

14 – English FUEL HANDLING Fuel mixture NOTE! The machine is fitted with a two-stroke engine and mustalways be run on a mixture of petrol and two-stroke oil. It isimportant to measure the quantity of oil accurately, to ensurethe correct mixture ratio. Small discrepancies in the amount ofoil have a g...

English – 15 START AND STOP Control before starting For reasons of safety followthese recommendations! • Check that the support flange is not cracked due tofatigue or due to beingtightened too much.Discard the support flangeif it is cracked. • Ensure the locking nut has not lost its captive force.Th...

16 – English Basic setting • The carburettor is set to its basic setting when test run at the factory. The basic setting is richer than the optimal settingand should be kept during the machine‘s first workinghours. Thereafter the carburettor should be finely adjusted.Fine adjustment should be carrie...

English – 17 MAINTENANCE H needle. The high speed needle is adjusted correctly when themachine ‘splatters’ a little . If the machine smokes heavily atthe same time as it ‘splatters’ heavily the adjustment is too rich. The high speed needleaffects the machine’s power,speed, temperature and fuelconsum...

18 – Française ENTRETIEN Circuit de refroidissement Pour obtenir unetempérature de service aussibasse que possible, le moteurest muni d’un circuit derefroidissement.Le système derefroidissement se composede:1. Prise d’air au niveau du démarreur. 2. Ailettes de ventilation sur la roue volante. 3. Ail...

English – 19 MAINTENANCE The angle gear is filled with asufficient quantity of grease atthe factory. However, beforeusing the machine you shouldcheck that the angle gear isfilled to 3/4 with grease. UseJONSERED special grease. Normally, the grease does notneed to be changed exceptwhen repairs are ca...

20 – English TECHNICAL DATA Technical data Engine Displacement, cu. in/cm 3 Cylinder bore, inch/mmStroke length, inch/mmRecommended max. speed, rpmIdling speed, rpmSpeed of output shaft, rpmMax. engine output, acc. to ISO 8893, kW/rpmCatalytic converter mufflerSpeed-regulated ignition system Ignitio...

English – 21 EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U.S. Environmental Protection Agency),Environment Canada and Jonsered are pleased to explainthe emissions control system warranty on your 2001 andlater small off-road engine. In U.S. and Canada, new smallo...

22 – English 1 Poly Trim 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10

English – 23 1 Trimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"

24 – English 1 Trimmy Hit Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"

English – 25 6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 1 2 3 4 5 6 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 11" Trimmy VII