Jonsered GC2236 - Manuals

GENERAL SAFETY PRECA UTIONS 6 – English Impor tant Personal protective equipment HELMET A protectiv e helmet where there is a risk of falling objects HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a vi...

GENERAL SAFETY PRECA UTIONS English – 7 BOO TS Wear boots with steel toe-caps and non-slip sole. CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure ha...

GENERAL SAFETY PRECA UTIONS 8 – English be chec ked. See instructions under the heading Maintenance. Stop switch Use the stop switch to switch off the engine. Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Cutting attachment guard This guard is int...

GENERAL SAFETY PRECAUTIONS English – 9 Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user. A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust gases. In countries that have a warm and dry climate there i...

GENERAL SAFETY PRECAUTIONS 10 – English Locking nut A locking nut is used to secure some types of cutting attachment. When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attach...

GENERAL SAFETY PRECAUTIONS English – 11 General rules Only use cutting attachments with the guards we recommend! See the chapter on Technical data. Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade i...

ASSEMBLY 12 – English Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Attach the J-handle to the loop handle...

ASSEMBLY English – 13 Fitting the guard extension CAUTION! The guard extension shall always be fitted when using the trimmer head/plastic blades and combination guard. The guard extension shall always be removed when using the grass blade and combination guard. Enter the guard extension guide in the...

FUEL HANDLING English – 15 Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use s...

FUEL HANDLING 16 – English Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. • Mix (shake) the fuel mi...

STARTING AND STOPPING English – 17 Check before starting • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that th...

STARTING AND STOPPING 18 – English Choke: Set the choke control in the choke position. Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pa...

WORKING TECHNIQUES English – 19 General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects...

WORKING TECHNIQUES 20 – English Basic working techniques Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Grass clearing using a grass blade • Grass blades and grass cutters must not be ...

MAINTENANCE 22 – English Carburettor Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and produces as little harmful exhaust...

MAINTENANCE English – 23 Low speed jet L Try to find the highest idle speed by turning the low speed jet L clockwise then anti-clockwise. When the highest speed has been found, turn the low speed jet L 1/4 turn anti-clockwise. CAUTION! If the cutting attachment rotates when the engine is idling the ...

MAINTENANCE 24 – English Muffler CAUTION! Some mufflers are fitted with a catalytic converter. See chapter on Technical data to see whether your machine is fitted with a catalytic converter. The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The...

MAINTENANCE English – 25 Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts. • Excessive fuel consumption. Clean the filter every 25 hours, or more reg...

26 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensiv...

English – 27 TECHNICAL DATA Technical data Note 1: Noise emissions in the environment measured as sound power (L WA ) in conformity with EC directive 2000/14/ EC. Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working c...

28 – English TECHNICAL DATA EC-declaration of conformity (Applies to Europe only) We, Jonsered, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saws Jonsered GC 2236 with serial numbers dating from 2006 onwards (the year is clearly stated on the rating plate, followed by t...

1 Poly Trim 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10

Tap n’ Go 35 Spin "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm

"Clic" 1 2 3 5 6 7 9 10 m 32' 4 8 4,3 m 14' 2,7-3,3 mm .106-.13" 10 cm 4" 6" 15 cm Tap n’Go 45 Spin