Jonsered CS 2152 EPA III - Manuals

GENERAL SAFETY PRECA UTIONS English – 7 Bef ore using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel ...

GENERAL SAFETY PRECA UTIONS 8 – English pro vide information about which training materials and courses are available. Work is constantly in progress to improve the design and technology - improvements that increase your safety and efficiency. Visit your dealer regularly to see whether you can benef...

GENERAL SAFETY PRECAUTIONS English – 9 • The brake is applied when the front hand guard (B) is pushed forwards. • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum). • The front hand guard is not designed solely to acti...

GENERAL SAFETY PRECAUTIONS 10 – English • In the felling position the left hand is in a position that makes manual activation of the chain brake impossible. With this type of grip, that is when the left hand is placed so that it cannot affect the movement of the front hand guard, the chain brake can...

GENERAL SAFETY PRECAUTIONS English – 11 The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine ′ s handle unit. The body of the chain saw, including the cutting equipment, is insulated from the handles by vibration damping...

GENERAL SAFETY PRECAUTIONS 14 – English • File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced. General advice on adjusting depth gauge setting • When you sharpen the cutting tooth (A) the depth gauge ...

GENERAL SAFETY PRECAUTIONS English – 15 Lubricating cutting equipment Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather. As a chain saw manufacturer we have developed an optimal ch...

ASSEMBLY English – 17 Fitting the bar and chain Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A). Fit the bar over the bar bolts. Place the...

FUEL HANDLING 18 – English Fuel Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts ...

FUEL HANDLING English – 19 • In temperatures below 32 ° F (0 ° C) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. Fueling Clean the area around the fuel cap. Clean the fuel and chain o...

STARTING AND STOPPING 20 – English Starting and stopping Cold engine Starting: The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards. Ignition; choke: Set the choke control in the choke position. This should automatically s...

STARTING AND STOPPING English – 21 As the chain brake is still activated the engine must return to idling speed as soon as possible by disengaging the throttle latch in order to avoid unnecessery wear on the clutch assembly. Note! Pull the front hand guard towards the front handle. The chain brake i...

WORKING TECHNIQUES 22 – English Before use: 1 Check that the chain brake works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle lockout works correctly and is not damaged. 4 Check that the stop switch works correctly and is not damaged. 5...

WORKING TECHNIQUES 24 – English 7 Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is known as cutting with a pushing chain. The chain tries to push the chain saw back towards the user. If the saw chain is jamming, the saw may be pus...

WORKING TECHNIQUES 26 – English Tree felling technique Safe distance The safe distance between a tree that is to be felled and anyone else working nearby is at least 2 1/2 tree lengths. Make sure that no-one else is in this ”risk zone” before or during felling. Felling direction The aim is to fell t...

WORKING TECHNIQUES 28 – English We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommen...

WORKING TECHNIQUES English – 29 How to avoid kickback What is kickback? The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar, known as the kickback zone, touches an object. Kickback always occu...

MAINTENANCE 30 – English General The user must only carry out the maintenance and service work described in this manual. Carburetor adjustment Due to existing environmental and emissions legislation your chain saw is equipped with movement limiters on the carburetor adjuster screws. These limit the ...

MAINTENANCE English – 31 High speed jet H At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet. CAUTION! If the high speed jet...

MAINTENANCE English – 33 Make sure the vibration damping units are securely attached to the engine unit and handle unit. Stop switch Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Muffler Never use a machine that has a faulty muffler. Regularly che...

MAINTENANCE 34 – English • Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards. • Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cor...

MAINTENANCE English – 35 The filter can be cleaned more thoroughly by washing it in water and detergent. An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be rep...

MAINTENANCE 36 – English Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Air guide plate. 3 Fins on the flywheel. 4 Cooling fins on the cylinder. 5 Cylinder cover (directs ...

MAINTENANCE English – 37 Heated handles (CS 2152W, CS 2153W) On models with the model code W, both the front handle bar and the rear handle are equipped with electrical heating coils. These are supplied with electricity from a generator built into the chain saw. When the switch is pushed downwards, ...

38 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Weekly maintenance Monthly maintenance Clean the outside of the machine. On chain saws without...

English – 39 TECHNICAL DATA Technical data CS 2152 CS 2153 Engine Cylinder displacement, cu.in/cm 3 3,15/51,7 3,06/50,1 Cylinder bore, inch/mm 1,77/45 1,74/44,1 Stroke, inch/mm 1,28/32,5 1,28/32,5 Idle speed, rpm 2700 2700 Power, kW/hp @ rpm 2,4/3,3 @ 9000 2,6/3,5 @ 9600 Ignition system Manufacturer...

40 – English TECHNICAL DATA Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the Jonsered chain saw models CS 2152 and CS 2153. The combinations of power head, bar and chain have been tested and found to be in accordance with th...

FEDERAL EMISSION CONTROL WARRANTY STATEMENT English – 41 YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2009 and later small nonroad engine. In U.S. and Canada...

AMERICAN STANDARD SAFETY PRECAUTIONS 42 – English Safety precautions for chain saw users (ANSI B 175.1-2000 Annex C) Kickback safety precautions With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents. Keep a good firm gri...