Jonsered 2125 - Manuals

English – 5 SAFETY INSTRUCTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. The machine ′ s vibrati...

6 – English SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′′′′ s safety equipment Throttle lock • Make sure the throttle control is locked at the idle setting when the throttle lock is released. • Press the throttle lock and make sure it returns to its original position when yo...

8 – English SAFETY INSTRUCTIONS Cutting equipment Sharpening grass cutters and grass blades • See the cutting attachment packaging for correct sharpening instructions. • Sharpen blades and cutters using a single-cut fl at fi le. • Sharpen all edges equally to maintain the balance of the blade. Trimm...

English – 9 SAFETY INSTRUCTIONS General safety precautions Starting • The complete clutch cover and shaft must be fi tted before the machine is started, otherwise the clutch can come loose and cause personal injury. • Never start the machine indoors. Exhaust fumes can be dangerous if inhaled. • Obse...

10 – English SAFETY INSTRUCTIONS • The transport guard must always be fi tted to the cutting attachment when the machine is being transported or in storage. General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control ...

12 – English WHAT IS WHAT? What is what on the trimmer? 30 1 Trimmer head 2 Grease fi ller cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle 12 Fuel tank 13 Choke control 14 Air purge 15 ...

English – 13 ASSEMBLY Fitting the loop handle (GT 2125) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Fitting the loop handle (GC 2125) • Clip the lo...

English – 15 ASSEMBLY Fitting other guards and cutting attachments (GC 2125) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fi tting on the shaft and secure with the bolt (L). • Fit the drive disc (B) on the output shaft. • Turn t...

16 – English FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing sm...

English – 17 FUEL HANDLING Fueling • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. • Ensure that the fuel is well mixed by shaking the container before fi lling the tank. ! WARNING! Taking the following precautions, will lessen the risk of fi re: Do not ...

18 – English STARTING AND STOPPING Check before starting • Check that the support fl ange is not cracked due to fatigue or due to being tightened too much. Discard the support fl ange if it is cracked. • Ensure the locking nut has not lost its captive force. The nut lock should have a locking force ...

English – 19 STARTING AND STOPPING some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never wrap the starter cord around your hand Repeat pulling the cord until the engine starts. When the engine starts. return choke control to run position and apply full throttle; t...

20 – English MAINTENANCE Carburetor Your Jonsered product has been designed and manufactured to speci fi cations that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and produces as little harmful exhaus...

English – 21 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting at...

22 – English MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder. 4 Cylinder cover (directs cold air over the...

English – 23 MAINTENANCE Spark plug The spark plug condition is in fl uenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dirty air fi lter. These factors cause deposits on the spark plug electrodes, which may result in operating problem...

24 – English TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...

26 – English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. In U.S. and Canada...

1 Trimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"