Page 2 - JL AUDIO; Woofer Physical Dimensions
2 JL AUDIO ZR650-CSi A E B F D C Woofer Physical Dimensions Frame Outer Diameter (A) 6.50 in. / 165.1 mm Grille Tray Outer Diameter (B) 6.76 in. / 171.7 mm Magnet Outer Diameter (C) 3.54 in. / 90.0 mm Frontal Grille Protrusion (D) 0.98 in. / 24.9 mm Mounting Hole Diameter (E) 5.56 in. / 141.3 mm Mou...
Page 3 - Mineral-filled polypropylene cone body,
JL AUDIO ZR650-CSi 3 ZR650-CSi SPECiFiCATiONS : Woofers: Mineral-filled polypropylene cone body, 1-inch (25mm) voice coil, low-profile/ symmetrical-roll spider, butyl rubber surround Tweeters: 1-inch (25 mm) aluminum dome tweeter with soft rubber suspension, neodymium magnet, ferrofluid cooled and d...
Page 4 - CROSSOVER NETWORK iNSTALLATiON :; DO NOT INSTALL THEM INSIDE OF; WARNiNG; Your crossovers are pre-
4 JL AUDIO ZR650-CSi GETTiNG STARTED : • Turn off the audio system. It is also advisable to disconnect the negative (–) terminal of your vehicle’s battery whenever performing installation work. • Before cutting, drilling or inser ting any screw, check clearances on both sides of the planned mounting...
Page 5 - Diagram A: Standard Wiring Diagram
JL AUDIO ZR650-CSi 5 Amplifier Output Woofer Amplifier Output Tweeter Amplifier Output Diagram A: Standard Wiring Diagram Diagram B: Bi-Wire (Bi-Amp) Wiring Diagram
Page 6 - CROSSOVER NETWORK ADjuSTMENT; The ZR crossover networks have been designed; ADjuSTABLE MiDRANGE PRESENCE :; Your ZR crossover networks provide a unique; ADjuSTABLE TWEETER LEVEL:; ZR crossover networks also provide five levels
6 JL AUDIO ZR650-CSi CROSSOVER NETWORK ADjuSTMENT The ZR crossover networks have been designed to allow tonal adjustments to the upper midrange response and tweeter level. These adjustments make it possible to f ine-tune your system to suit your listening preferences and to compensate for various sp...
Page 7 - A component system gives you the ability to place
JL AUDIO ZR650-CSi 7 SPEAKER PLACEMENT CONSiDERATiONS : A component system gives you the ability to place the woofer and tweeter separately in your vehicle interior. This can be good or bad, depending on how it’s done. As a general rule, the tweeters should be placed relatively close to the woofers ...
Page 8 - WOOFER iNSTALLATiON :; Keep in mind that the woofer wires
8 JL AUDIO ZR650-CSi Custom Location: Run speaker wire to the desired mounting locations. If you are running wires into a door, use existing factory wiring boots whenever possible. If you are drilling new holes, file their edges and install rubber grommets into each hole. Wires should then be covere...
Page 9 - Diagram D: Custom Location Woofer Installation; Diagram C: Factory Location Woofer Installation
JL AUDIO ZR650-CSi 9 Diagram D: Custom Location Woofer Installation ! ! WARNiNG ! ! Hand-tighten the screws evenly in a criss-cross pattern to avoid bending the speaker frame or stripping the mounting clips. Diagram C: Factory Location Woofer Installation
Page 10 - TWEETER iNSTALLATiON :; First, run speaker wires from the tweeter output; TWEETER FiXTuRE iNSTALLATiON :; The dome tweeters supplied with your
10 JL AUDIO ZR650-CSi TWEETER iNSTALLATiON : First, run speaker wires from the tweeter output of the crossover (see diagrams on page 5) to the desired tweeter mounting locations, observing the same precautions as mentioned in the woofer installation section. Terminate the wires with the supplied 2.8...
Page 11 - Diagram F: Surface-Mount Tweeter Installation
JL AUDIO ZR650-CSi 11 Diagram F: Surface-Mount Tweeter Installation Diagram E: Flush-Mount Tweeter Installation
Page 12 - if you need service on your jL AuDiO product:; during normal business hours (Eastern Time); international Warranties:; by that countr y’s distributor and not by JL Audio, Inc.
jL AuDiO LiMiTED WARRANTy (uSA) Automotive Speaker Systems JL Audio warrants these speakers (and crossover networks, where applicable) to be free of defects in materials and workmanship for a period of one (1) year . This warranty is not transferrable and applies only to the original purchaser from ...