JL Audio XD200/2 - Manuals - manualsarea.com

Page 4 - PRODUCT DESCRIPTION; The XD200/2 can be operated with a wide; TYPICAL INSTALLATION SEQUENCE; The following represents the sequence

4 | JL Audio - XD200/2 Owner’s Manual PRODUCT DESCRIPTION The JL Audio XD200/2 is a two-channel, full-range audio amplifier utilizing JL Audio NexD™ ultra-high speed switching technology to deliver outstanding fidelity and efficiency. The XD200/2 can be operated with a wide variety of source units a...

Page 6 - INPUT SECTION

6 | JL Audio - XD200/2 Owner’s Manual TURN-ON LEAD The XD200/2 uses a conventional +12V remote turn-on lead, typically controlled by the source unit's remote turn-on output. The amplifier will turn on when +12V is present at its “Remote” input and turn off when +12V is switched off. If a source unit...

Page 7 - To properly set the amplifier for maximum; Do not increase any “Input Sens.” setting for

7 INPUT SENSITIVITY CONTROL The control labeled “Input Sens.” can be used to match the source unit’s output voltage to the input stage of the amplifier for maximum clean output. Rotating the control clockwise will result in higher sensitivity (louder for a given input voltage). Rotating the control ...

Page 8 - FILTER CONTROLS; Most speakers are not designed to reproduce

8 | JL Audio - XD200/2 Owner’s Manual FILTER CONTROLS Most speakers are not designed to reproduce the full range of frequencies audible by the human ear. For this reason, most speaker systems are comprised of multiple speakers, each dedicated to reproducing a specific frequency range. Filters are us...

Page 9 - PREOUTS; The preamp output delivers the same signal

9 REMOTE LEVEL CONTROL (OPTIONAL) With the addition of the optional Remote Level Control (HD-RLC), you can control the volume of the XD200/2 from the front of the vehicle. This is useful for subwoofer level control, rear channel level control, center-channel level control or even as a master volume ...

Page 10 - SPEAKER OUTPUTS; The XD200/2’s speaker outputs are designed; BRIDGING CONSIDERATIONS; Bridging is the practice of combining the

10 | JL Audio - XD200/2 Owner’s Manual SPEAKER OUTPUTS The XD200/2’s speaker outputs are designed to accept 16 AWG - 8 AWG wire. To connect the speaker wires to the amplifier, first back out the set screws on the top of the terminal block, using the supplied 2.5 mm hex wrench. Strip 1/2 inch (12 mm)...

Page 11 - STATUS LED / PROTECTION CIRCUITRY; There is a single multi-color LED on the top; SERVICING YOUR JL AUDIO AMPLIFIER; If your amplifier fails or malfunctions, please

11 STATUS LED / PROTECTION CIRCUITRY There is a single multi-color LED on the top surface of the amplifier to indicate the amplifier’s operating status. 1) Flashing Green: amplifier is powering up,audio output is muted. 2) Constant Green: amplifier is on andfunctioning normally, audio output is acti...

Page 12 - Following the directions below will allow the; Necessary Equipment; amplifier’s speaker output connectors.; Impedance; not recommended

12 | JL Audio - XD200/2 Owner’s Manual APPENDIX A:Input Sensitivity Level Setting Following the directions below will allow the installer to adjust the input sensitivity of the XD200/2 simply and easily in just a few minutes using equipment which is commonly available in installation bays. Necessary...

Page 13 - General Specifications:; Recommended Fuse Value:; Rated Power at 14.4V with less than; Signal to Noise Ratio:; “FILTER FREQ”; Detent Panel Actual

13 APPENDIX C:XD200/2 Specifications General Specifications: Recommended Fuse Value: 20A Recommended Fuse Type: MAXI® or AGU Input Sections: No. of Inputs: One Stereo Pair Input Type: Differential-balanced with RCA jack inputs Input Range: 100mV - 4V RMS Amplifier Section: Amplifier Topology: NexD™ ...

Page 14 - contact with the input jacks on the amplifier.; APPENDIX D: TROUBLESHOOTING

14 | JL Audio - XD200/2 Owner’s Manual “How do I properly set the input sensitivity on my amplifier?” Please refer to Appendix A (page 12) to set the input sensitivity for maximum, low-distortion output. “My amplifier doesn’t turn on.” Check the fuse, not just visually, but with a continuity meter. ...

Page 20 - If you need service on your JL AUDIO product:; (do not send product for repair to this address); International Warranties:; by that country’s distributor and not by JL Audio, Inc.

LIMITED WARRANTY - AMPLIFIERS (USA) JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years. The warranty is extended to three (3) years total if installation is performed by an authorized JL Audio dealer using a JL Audio Premium Power Connecti...