JAI CV-A1 - Manuals - manualsarea.com

Page 2 - Table of Contents

CV-A1 Table of Contents 1. General......................................................................................................... 2 2. Standard Composition ....................................................................................... 2 3. Main Features ..............................

Page 3 - Standard Composition

CV-A1 1. General The CV-A1 is a monochrome progressive scan 1/2” CCD camera with 1.4 Megapixel resolution. It is designed for automated inspection, featuring a small housing and a wide range of unique functions. The asynchronous trigger can be set to work in several modes, to allow such functions as...

Page 4 - Locations and Functions; Gain potentiometer for manual gain setting.

CV-A1 4. Locations and Functions Fig. 1. Locations. 1. 12 pin Hirose connector for frame grabber interfacing and power (12V DC). 2. BNC connector for video output. VS 1.0 Vpp 75 Ohm. 3. 6 pin Hirose connector for trigger input and RS-232C control interface. 4. Gain potentiometer for manual gain sett...

Page 5 - Parallel with the BNC connector.; Signal

CV-A1 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear Pin configuration is compatible with EIAJ standard Fig. 2. 12-pin connector. Plugs for cable: HR10A-10P-12S 5.2. 6-pin Multi-connector (TRIGGER) Type: HR10A-7R-6PB...

Page 7 - Functions and Operations; SM; Imaged scene

CV-A1 5.4. CV-A1 Block Diagram Fig. 8. Block diagram. 6. Functions and Operations 6.1. Basic functions Some of the primary camera functions need a general introduction before the operation modes are described. The list below shows the primary functions from the command list. SM Shutter Mode Normal s...

Page 8 - The accumulation mode; Trigger modes with possible scanning and binning combinations

CV-A1 Binning mode BI is a function where the signal charge from 2 or more adjacent pixels are added together and read out as one pixel. A resulting full frame with lower resolution can be read out with a higher rate. By adding 2 pixels together, the sensitivity is doubled. The CV-A1 has both vertic...

Page 9 - HD VD

CV-A1 6.2. Input-output of HD/VD Signals In the default setting the camera will accept external HD/VD signals on pin 6 and 7 of the 12 pin Hirose connector. If external HD/VD is applied, the camera will synchronize to it. If no external sync signals are applied, the camera will operate with its inte...

Page 11 - Fig.18. Pulse Width H Synchronous Accumulation

CV-A1 6.4. External Trigger Modes This camera has 6 external asynchronous trigger modes, which can be set by RS-232C commands. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure. (HC=0, HC=1) 3. Frame Delay read out mode...

Page 12 - Important notes on using this mode.

CV-A1 6.5. Edge Pre-select Mode The exposure starts at the first HD pulse after the trigger leading edge. It stops and is read out after the duration of the shutter time selected. It can be the first 9 step in normal or 1023 steps in programmable shutter. SM=0 or SM=1. Shutter selections SH ≥ 10 wil...

Page 14 - Table showing the figures for the different modes.; Binning

CV-A1 6.7. Frame-delay read out Mode In this mode the exposure starts from the leading edge of the trigger pulse. It stops at the trailing edge of the trigger pulse. The accumulation can be either H synchronous or H asynchronous. HC=0 or HC=1. In H synchronous mode the accumulation starts at the fir...

Page 18 - Configuring the Camera

CV-A1 6.11. Other Functions. Gain and analogue settings. !! Do not adjust these settings unless you have knowledge to video adjustments !! The video gain can be set to AGC or manual . In AGC mode the video level is kept constant by the automatic gain control circuit within a 12 dB range. Normal 700 ...

Page 21 - Internal Switch and Jumper Settings; Fuse; External Appearance and Dimensions

CV-A1 7.4. Internal Switch and Jumper Settings For VD and HD input/output and termination refer to “6.2. Input-output of HD/VD Signals.” For alternative connections of pin #10 and #11 on 12-pin connector, jumper JP1, JP2, JP3, JP4 and JP5 can be used. Refer “5.3. Input and Output Circuits.” Jumper s...

Page 22 - Spectral Sensitivity

CV-A1 9. Specifications Specifications CV-A1 Scanning system Progressive 1068 lines 16.037 frames/sec. Pixel clock 28.63636 MHz Line frequency 17.127 kHz (1672 pixel clock/line) Frame rate for full frame 16.037 frames/sec. (1068 lines/frame) CCD sensor 1/2” progressive monochrome IT CCD. Sony ICX205...

Page 24 - DECLARATION OF CONFORMITY; AS DEFINED BY THE COUNCIL DIRECTIVE

CV-A1 11. Users Record Camera type: CV-A1 Revision: (Revision B) Serial No. …………….. Users Mode Settings Users Modifications DECLARATION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EEC EMC (ELECTROMAGNETIC COMPABILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWING PROV...