Page 2 - SPECIAL NOTES; NOTICE; WARNING
Invacare Scooters 2 Part No. 1090132 Rev F WARNING WARNING WARNING WARNING WARNING WARNING DO NOT OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS AND INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL, DEALER OR TECHNICA...
Page 3 - TABLE OF CONTENTS; TABLE
Part No. 1090132 Rev F 3 Invacare Scooters TABLE OF CONTENTS TABLE OF CONTENTS SPECIAL NOTES ................................................................................ 2SPECIFICATIONS .............................................................................. 4PROCEDURE 1 - GENERAL GUIDELIN...
Page 5 - SPECIFICATIONS; NOTE: Flat free inserts are standard on all wheels.
Part No. 1090132 Rev F 5 Invacare Scooters SPECIFICATIONS SPECIFICATIONS v NOTE: Flat free inserts are standard on all wheels. *NOTE: Total weight of scooter includes Contour Seat Only. Add an additional 9-lbs for Deluxe Seat. SPECIFICATIONS Overall Length: 39.5-inches (100 cm) 43.5-inches (104 cm) ...
Page 7 - PROCEDURE 1; GENERAL
Part No. 1090132 Rev F 7 Invacare Scooters PROCEDURE 1 GENERAL GUIDELINES GENERAL WARNINGS OPERATING INFORMATION Performance adjustments should ONLY be made by professionals of the healthcare field or persons fully conversant with this process and the driver's capabilities. Incorrect settings could ...
Page 8 - from the ignition. This will ensure that the power is off and the
Invacare Scooters 8 Part No. 1090132 Rev F GENERAL WARNINGS (CONTINUED) OPERATING INFORMATION (Continued)Before attempting to sit in or exit the powered scooter, REMOVE the key from the ignition. This will ensure that the power is off and the powered scooter will not drive.Remove the key from the ig...
Page 9 - EMI WARNINGS
Part No. 1090132 Rev F 9 Invacare Scooters GENERAL WARNINGS (CONTINUED) GROUNDING INSTRUCTIONS: DO NOT, under any circumstances, cut or remove the round grounding prong from any plug. Some devices are equipped with three-prong (grounding) plugs for protection against possible shock hazards. Where a ...
Page 10 - fire trucks, ambulances, and taxis. These usually have the antenna
Invacare Scooters 10 Part No. 1090132 Rev F EMI WARNINGS (CONTINUED) Powered scooters may be susceptible to electromagnetic interference (EMI), which is interfering electromagnetic energy (EM) emitted from sources such as radio stations, TV stations, amateur radio (HAM) transmitters, two way radios,...
Page 12 - safety as the most important; STABILITY AND BALANCE; and stable during normal daily activities.; PERCENTAGE OF WEIGHT DISTRIBUTION
Invacare Scooters 12 Part No. 1090132 Rev F PROCEDURE 1 GENERAL GUIDELINES SAFETY/HANDLING Safety and Handling of the powered scooter requires the close attention of the user. This manual points out the most common procedures and techniques involved in the safe operation and maintenance. It is imp...
Page 13 - STAIRWAYS; tor is NOT available:; reassemble the scooter. Refer to TRANSPORTING in
Part No. 1090132 Rev F 13 Invacare Scooters STAIRWAYS WARNING DO NOT attempt to move an occupied powered scooter between floors using a stairway. Use an elevator to move an occupied powered scooter between floors.If moving a powered scooter between floors by means of a stairway, the occupant MUST be...
Page 14 - WARNING/CAUTION LABEL LOCATION
Invacare Scooters 14 Part No. 1090132 Rev F WARNING/CAUTION LABEL LOCATION DELTA TILLER STANDARD TILLER NOTE: Not included on ZOOM- 3. ZOOM-3 is equipped with non-removable anti-tip tubes. PROCEDURE 1 GENERAL GUIDELINES GENERAL GUIDELINES ! WARNING Remove key from the ignition while scooter is not i...
Page 15 - SAFETY INSPECTION/MAINTENANCE; Thereafter follow these maintenance procedures:; SAFETY
Part No. 1090132 Rev F 15 Invacare Scooters This Procedure Includes the Following:Safety Inspection ChecklistMaintenanceTroubleshooting SAFETY INSPECTION/MAINTENANCE NOTE: Every six (6) months take the scooter to a qualified technician for a thorough inspection and servicing. Regular cleaning will r...
Page 16 - PROCEDURE 2; MAINTENANCE; SUGGESTED MAINTENANCE PROCEDURES; be replaced by a qualified technician.
Invacare Scooters 16 Part No. 1090132 Rev F PROCEDURE 2 SAFETY INSPECTION/MAINTENANCE SAFETY INSPECTION/ MAINTENANCE ITEM INITIALLY INSPECT/ADJUST WEEKLY MONTHLY PERIODICALLY TIRES (PROCEDURE 9) Inspect for flat spots and wear. X X If pneumatic tires check for proper inflation. X X CAUTION: As with ...
Page 17 - Pont Nemours and Company.; FIGURE 1 - LUBRICATION POINTS; DETAIL
Part No. 1090132 Rev F 17 Invacare Scooters LUBRICATION POINTS (FIGURE 1) 1. Every six (6) months the following components should be lubricated. Use a Teflon ® lubricant if necessary (FIGURE 1) . A. Seat Lever, Connecting Pin, and Release Pin.B. Top of Seat Adaptor. Note: Teflon - Registered tradema...
Page 18 - TROUBLESHOOTING GUIDE
Invacare Scooters 18 Part No. 1090132 Rev F SAFETY INSPECTION/MAINTENANCE PROCEDURE 2 TROUBLESHOOTING GUIDE SAFETY INSPECTION/ MAINTENANCE SYMPTOM LIMITED DRIVING DISTANCE. BATTERIES NOT CHARGING. BATTERIES DRAW EXCESSIVE CURRENT WHEN CHARGING.CHARGE INDICATOR SHOWS LOW CHARGE LEVEL IMMEDIATELY AFTE...
Page 19 - CONTROL PANEL FEATURES; ALL SCOOTER MODELS; - Located on the top face of the control panel. The number; OPERATION
Part No. 1090132 Rev F 19 Invacare Scooters PROCEDURE 3 OPERATION WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely. Otherwise, injury or damage may result. CONTROL PANEL FEATURES ALL SCOOTER MODELS With Delta or Standard Til...
Page 21 - PANTHER MX-4 SCOOTERS; NOTE: Switching from HIGH speed to LOW speed
Part No. 1090132 Rev F 21 Invacare Scooters With Delta Tillers (FIGURE 3). 1. Ignition - Located on front face of the tiller. 2. Headlight Button - Located on the right side of the tiller. 3. Throttle Control Levers - Located centralized to the handle grips of the tiller. PANTHER MX-4 SCOOTERS ONLY ...
Page 22 - PROCEDURE 3; faster speed may be necessary.; side throttle control lever.
Invacare Scooters 22 Part No. 1090132 Rev F PROCEDURE 3 OPERATION OPERATION OPERATION OF THE SCOOTER (FIGURES 1-5) WARNING Before attempting to sit in the powered scooter, REMOVE the key from the ignition. This will ensure that the POWER is OFF and the scooter will not drive.To determine and establi...
Page 23 - CAUTION; HAND BRAKE LEVER
Part No. 1090132 Rev F 23 Invacare Scooters USING THE HAND BRAKE LEVER/BRAKE ARM (FIGURE 6) NOTE: The hand brake lever and brake arm are only on the PANTHER MX-4 (Without Delta Tiller). CAUTION ALWAYS release throttle control lever BEFORE using the hand brake. Using the hand brake in conjunction wit...
Page 24 - BRAKE RELEASE LEVER; NOTE: Remove key and disengage brake
Invacare Scooters 24 Part No. 1090132 Rev F PROCEDURE 3 OPERATION OPERATION BRAKE RELEASE LEVER CAUTION Ensure that the brake-release lever is in the ON position (engaged) before driving. There should be an audible "click" when stopping and starting. BRAKE-RELEASE LEVER - Manually engages an...
Page 25 - CIRCUIT BREAKER; To reset, press circuit breaker button located on rear shroud.; FUSE REPLACEMENT; in PROCEDURE 5; FIGURE 9 - RESET CIRCUIT BREAKER/FUSE REPLACEMENT
Part No. 1090132 Rev F 25 Invacare Scooters RESET CIRCUIT BREAKER/FUSE REPLACEMENT (FIGURE 9) CIRCUIT BREAKER NOTE: Key must be removed from ignition before resetting circuit breaker. 1. To reset, press circuit breaker button located on rear shroud. FUSE REPLACEMENT 1. Remove seat. Refer to REMOVING...
Page 26 - PROCEDURE 4; REMOVING/INSTALLING THE BATTERIES WITH CABLES; REMOVING; in PROCEDURE 5 in this manual.
Invacare Scooters 26 Part No. 1090132 Rev F BATTERIES/CHARGING PROCEDURE 4 BATTERIES/CHARGING This Procedure Includes the Following:Removing/Installing the Batteries with CablesReplacing the BatteriesCharging the Batteries WARNING After ANY adjustments, repair or service and BEFORE use, make sure th...
Page 27 - black connectors of the controller wiring harness.; RECOMMENDED BATTERY TYPES
Part No. 1090132 Rev F 27 Invacare Scooters SCOOTER QTY VOLTS AMP MODEL HOURS ZOOM-3 2 12 12 LYNX SX-3 2 12 17 LYNX LX-3 2 12 31 LYNX LX-3 Plus 2 12 31 PANTHER LX-4 2 12 31 PANTHER MX-4 2 12 40 5. Disconnect red and black connectors of the battery wiring harness from red and black connectors of the ...
Page 29 - CLEANING BATTERY TERMINALS; AND
Part No. 1090132 Rev F 29 Invacare Scooters CLEANING BATTERY TERMINALS WARNING DO NOT allow conductive material such as a wrench to join the two (2) battery terminals. This will result in a dead short that can cause burns to you and dam- age to the battery.Most batteries are not sold with instructio...
Page 30 - Carefully dust off all metal particles.; CHARGING THE BATTERIES
Invacare Scooters 30 Part No. 1090132 Rev F BATTERIES/CHARGING PROCEDURE 4 BATTERIES/CHARGING NOTE: Upon completion, these areas should be shiny, not dull. 3. Carefully dust off all metal particles. CHARGING THE BATTERIES WARNING Never attempt to recharge the batteries by attaching cables directly t...
Page 31 - REMOTE BATTERY; FIGURE 3 - CHARGING THE; NOTE: Charger Port Covers pivot; FIGURE 4 - CHARGING THE
Part No. 1090132 Rev F 31 Invacare Scooters REMOTE BATTERY CHARGER (FIGURE 3) 1. Open the charger port cover located on the left side of the tiller. 2. Plug charger connector into charger port. 3. Plug charger into standard 110-volt wall outlet. 4. Refer to BATTERY CHARGER OPERATION in this procedur...
Page 32 - driven while the charger is plugged in to an outlet.
Invacare Scooters 32 Part No. 1090132 Rev F BATTERIES/CHARGING PROCEDURE 4 BATTERIES/CHARGING BATTERY CHARGER OPERATION (FIGURE 5) 1. The ON/OFF LED indicator will illuminate Solid Red indicating that the charger is ON. 2. If the ON/OFF LED indicator is " Blinking " Red , this is abnormal. P...
Page 33 - PROCEDURE 5; REMOVING/INSTALLING THE SEAT; SEAT; FIGURE 1 - DETERMINING SEAT
Part No. 1090132 Rev F 33 Invacare Scooters PROCEDURE 5 SEAT This Procedure Includes the Following:Removing/Installing the SeatAdjusting the Seat Height90º Seat Swivel AdjustmentAdjusting the Seat DepthUsing the Adjustable Seat SlideRemoving/Installing Seat Upholstery/Cushion WARNING After ANY adjus...
Page 34 - on the SIDES of the frame post.
Invacare Scooters 34 Part No. 1090132 Rev F PROCEDURE 5 SEAT REMOVING (FIGURE 2) 1. Remove the stability knob located under the seat on the frame post. CAUTION When the seat height adjustment pin is removed, the weight of the seat assembly MUST be supported to prevent the seat from falling onto the ...
Page 35 - ADJUSTING THE SEAT HEIGHT; and front wheel are not shown for clarity.
Part No. 1090132 Rev F 35 Invacare Scooters PROCEDURE 5 SEAT SEAT NOTE: When installing the seat height adjustment pin, it is necessary to support the weight of the seat assembly. C. For adjustable seat seat post ZOOM-3 - install seat assembly onto seat post with the seat in the forward position. 4....
Page 37 - 0o SEAT SWIVEL ADJUSTMENT; ADJUSTING THE SEAT DEPTH; Swivel Release Lever; NOTE: Only the Contour Seat shown for clarity.; Seat
Part No. 1090132 Rev F 37 Invacare Scooters PROCEDURE 5 SEAT SEAT 90º SEAT SWIVEL ADJUSTMENT ALL MODELS EXCEPT ZOOM-3 (FIGURE 5) WARNING Ensure that seat is locked into the forward position BEFORE and DUR- ING operation of the scooter. Otherwise, injury to the user and/or dam- age to the scooter may...
Page 38 - USING THE ADJUSTABLE SEAT SLIDE (FIGURE 7)
Invacare Scooters 38 Part No. 1090132 Rev F 6. Secure all three (3) components together with the four (4) EXISTING mounting screws, lockwashers, and washers in the following manner: WARNING The two (2) longer mounting screws MUST be used to secure the rear of the seat assembly together and the two (...
Page 39 - NOTE: This procedure applies to the Contour; Unbutton the snap buttons of the seat; INSTALLING; Secure seat upholstery to seat with; INSTALLING THE SEAT
Part No. 1090132 Rev F 39 Invacare Scooters REMOVING/INSTALLING THE SEAT UPHOLSTERY/ CUSHION (FIGURE 8) NOTE: This procedure applies to the Contour Seat Only. Seat upholstery on the Deluxe seat CANNOT be removed. REMOVING 1. Unbutton the snap buttons of the seat upholstery located on the rear of the...
Page 40 - FOLDING/UNFOLDING THE; BACK
Invacare Scooters 40 Part No. 1090132 Rev F WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result. FOLDING/UNFOLDING THE BACK (FIGURE 1) 1. To fold, push back down towards seat.2. To unfold...
Page 41 - ADJUSTING THE BACK RECLINE; outside jam nuts to secure mounting; ADJUSTING THE HEADREST
Part No. 1090132 Rev F 41 Invacare Scooters ADJUSTING THE BACK RECLINE ALL MODELS EXCEPT ZOOM-3, SX-3 AND LX-3 (FIGURE 3) 1. Loosen the outside jam nut.2. Adjust mounting screw up or down to obtain the desired back angle.3. Thread inside jam nut upwards to the top edge of the back bracket.4. Securel...
Page 42 - ARMREST ANGLE ADJUSTMENT; ALL SEATS BUILT AFTER 10/; ARMREST WIDTH; ALL MODELS EXCEPT ZOOM-3; Adjustment Knob; NOTE: Only Contour Seat shown for clarity.
Invacare Scooters 42 Part No. 1090132 Rev F ARMS PROCEDURE 7 This Procedure Includes the Following:Armrest Angle AdjustmentArmrest Width AdjustmentArmrest Depth/Height Adjustment WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened secur...
Page 43 - ARMREST DEPTH/HEIGHT ADJUSTMENT; NOTE: These options are NOT available on; DEPTH
Part No. 1090132 Rev F 43 Invacare Scooters ARMS PROCEDURE 7 BACK ARMREST DEPTH/HEIGHT ADJUSTMENT ALL MODELS EXCEPT ZOOM-3 (FIGURE 3) NOTE: These options are NOT available on the CONTOUR SEATS Built BEFORE 10/00. DEPTH 1. Loosen bottom adjustment knob.2. Adjust armrest to desired position.3. Retight...
Page 44 - PROCEDURE 8; TILLER ANGLE ADJUSTMENT; in
Invacare Scooters 44 Part No. 1090132 Rev F This Procedure Includes the Following:Tiller Angle Adjustment PROCEDURE 8 TILLER ADJUSTMENT WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise, injury or damage may resul...
Page 45 - LOCKED
Part No. 1090132 Rev F 45 Invacare Scooters ALL OTHER MODELS (FIGURE 2) NOTE: The Powered Scooters features an adjustable tiller. This allows you to lock the tiller in to a position that is most comfortable for you. It also lets you fold down the tiller for transport and storage.NOTE: The angle adju...
Page 46 - NOTE: During initial use of scooter, user may
Invacare Scooters 46 Part No. 1090132 Rev F PROCEDURE 9 SHROUD/WHEELS This Procedure Includes the Following:Removing/Installing the Rear ShroudReplacing Foam Filled Tires Onto Wheel RimsRemoving/Installing the Rear WheelsRemoving/Installing the Front Wheel WARNING After ANY adjustments, repair or se...
Page 47 - TILLER; PROCEDURE 9
Part No. 1090132 Rev F 47 Invacare Scooters REMOVING/INSTALLING THE REAR WHEELS (FIGURE 2) REMOVING WARNING Turn Power OFF and remove key from ignition. 1. Turn Power OFF and remove key from ignition.2. Remove the seat. Refer to REMOVING/INSTALLING THE SEAT in PROCEDURE 5 of this manual. 3. Remove t...
Page 48 - NEW locking washer parallel.
Invacare Scooters 48 Part No. 1090132 Rev F NOTE: Use a rubber hammer if necessary to help position rear wheel completely onto the drive shaft. 7. Install the hex screw through the MIDDLE mounting hole in the locking tab washer, large washer and wheel hub. Securely tighten. 8. Visually inspect the h...
Page 49 - Securely tighten front wheel mounting hardware.; DO NOT USE TOP
Part No. 1090132 Rev F 49 Invacare Scooters PROCEDURE 9 SHROUD/WHEELS REMOVING 1. Turn Power OFF and remove key from ignition.2. Place the front of the powered scooter up on blocks so that the front wheel is OFF the ground.3. Remove the hardware that secures the front wheel to the mounting fork/fron...
Page 50 - TRANSPORTING THE SCOOTER (FIGURES 1 AND 2); DISASSEMBLING THE SCOOTER; NOTE: To reassemble the scooter, reverse the following steps.; ONLY; have been consolidated for ease of use.; For Models Built With Delta Tillers:; TRANSPORT
Invacare Scooters 50 Part No. 1090132 Rev F PROCEDURE 10 TRANSPORT This Procedure Includes the Following:Transporting the Scooter WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise, injury or damage may result. TRA...
Page 51 - FIGURE 1 - TRANSPORTING THE SCOOTER - FOR ALL MODELS; ORANGE Connectors
Part No. 1090132 Rev F 51 Invacare Scooters PROCEDURE 10 TRANSPORT TRANSPORT DETAIL "A" - MODELS BUILT WITHOUT DELTA TILLERS - EXCEPT ZOOM-3 AND PANTHER MX-4 FIGURE 1 - TRANSPORTING THE SCOOTER - FOR ALL MODELS EXCEPT ZOOM-3 DETAIL "B" - MODELS BUILT WITH DELTA TILLERS Tiller Wiring ...
Page 52 - NOTE: Side view shows location of Hand Brake Cable.
Invacare Scooters 52 Part No. 1090132 Rev F TRANSPORT PROCEDURE 10 8. For Panther MX-4 Models Built Before 10/00 - Without Delta Tillers (FIGURE 3): WARNING When reassembling scooter, ensure retaining pin is properly engaged in the hand brake cable. Otherwise, injury and/or damage may result. A. Pul...
Page 53 - FIGURE 2 - TRANSPORTING THE SCOOTER
Part No. 1090132 Rev F 53 Invacare Scooters WARNING When reassembling scooter, ensure retaining pin is properly engaged securing the front and rear frame together. Otherwise, injury and/or damage may result. 9. Pull retaining pin that secures the rear frame and front frame assemblies together (FIGUR...
Page 54 - A. Align slots of basket with mounting clips on shroud of tiller.; B. Push down on basket to secure in place.; OPTIONS/REPLACEMENT PARTS; FIGURE 1 - REMOVING/INSTALLING THE FRONT BASKET; NOTE: ONLY Standard Tiller shown for clarity.
Invacare Scooters 54 Part No. 1090132 Rev F This Procedure Includes the Following:Removing/Installing the Front BasketRemoving/Installing the Floor BasketRemoving/Installing the Seat Positioning StrapsRemoving/Installing the Crutch/Cane HolderRemoving/Installing the Safety FlagReplacing the Anti-Tip...
Page 55 - up against the rear shroud.; REMOVING/INSTALLING THE SEAT POSITIONING STRAP; FIGURE 2 - REMOVING/INSTALLING THE FLOOR BASKET
Part No. 1090132 Rev F 55 Invacare Scooters REMOVING/INSTALLING THE FLOOR BASKET (FIGURE 2) 1. To remove, remove the two (2) thumb screws that secure the floor basket in place. NOTE: The front basket must be installed with angled side facing the front and the vertical side up against the rear shroud...
Page 56 - REMOVING/INSTALLING THE CRUTCH/CANE HOLDER
Invacare Scooters 56 Part No. 1090132 Rev F REMOVING/INSTALLING THE SAFETY FLAG (FIGURE 5) NOTE: To remove, reverse the following procedure. WARNING The installation of the safety flag onto the back of the scooter seat significantly increases the length of the scooter. When turning the scooter or sw...
Page 57 - REPLACING ANTI-TIPPER WHEELS AND ANTI-TIPPER; and locknut that secures the anti-; all other models; cotter pin and washer that secure the; ASSEMBLY; NOTE: Anti-tipper wheel assemblies are only; and; TIPPER WHEELS AND ANTI-; Frame
Part No. 1090132 Rev F 57 Invacare Scooters OPTIONS/REPLACEMENT PARTS PROCEDURE 11 REPLACING ANTI-TIPPER WHEELS AND ANTI-TIPPER WHEEL ASSEMBLY (FIGURE 6) WARNING DO NOT operate scooter without the anti-tippers being installed, if so equipped. Anti-tippers MUST BE attached at all times. ANTI-TIPPER W...
Page 58 - REPLACING SEAT LEVER
Invacare Scooters 58 Part No. 1090132 Rev F PROCEDURE 11 REPLACING SEAT LEVER (FIGURE 7) NOTE: The seat lever is NOT available on ZOOM-3. 1. Remove the seat. Refer to REMOVING/INSTALLING THE SEAT in PROCEDURE 5 of this manual. 2. Place seat upside down on ground/floor.3. Remove cotter pin that secur...
Page 59 - REPLACING TILLER ANGLE ADJUSTMENT LEVER; NOTE: The tiller angle adjustment lever is; REPLACING HEADLIGHT LIGHTBULBS; FIGURE 8 - REPLACING TILLER; HEADLIGHT LIGHTBULBS
Part No. 1090132 Rev F 59 Invacare Scooters OPTIONS/REPLACEMENT PARTS PROCEDURE 11 REPLACING TILLER ANGLE ADJUSTMENT LEVER (FIGURE 8) NOTE: The tiller angle adjustment lever is NOT available on ZOOM-3. 1. Adjust the tiller so that the position of the tiller is in-between adjustment holes. NOTE: This...
Page 60 - sponding slots on the headlight assembly.; FIGURE 10 - REPLACING HEADLIGHT LIGHTBULBS
Invacare Scooters 60 Part No. 1090132 Rev F OPTIONS/REPLACEMENT PARTS PROCEDURE 11 MODEL PANTHER MX-4 (FIGURE 10) NOTE: Prongs on lightbulb plug are not equally spaced around diameter. Once removed, lightbulb plug can only be installed with prongs in the orientation in which they were removed. 1. Be...
Page 61 - FIGURE 11 - REPLACING ON-BOARD BATTERY CHARGER
Part No. 1090132 Rev F 61 Invacare Scooters REPLACING ON-BOARD BATTERY CHARGER (FIGURE 11) 1. Remove seat. Refer to REMOVING/INSTALLING SEAT in PROCEDURE 5 of this manual. 2. Remove the rear shroud. Refer to REMOVING/INSTALLING THE REAR SHROUD in PROCEDURE 9 of this manual. 3. Remove the floor baske...
Page 62 - NOTES; NOTES
Invacare Scooters 62 Part No. 1090132 Rev F NOTES NOTES NOTES
Page 63 - LIMITED WARRANTY; LIMITED W
Part No. 1090132 Rev F 63 Invacare Scooters LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.This warranty is extended only to the original purchaser/user of our products.This warranty gives you specif...