InFocus IN82 - Manuals

4 Connector Panel Remove the cable cover, if attached, to access the connector panel. Replace the cover after the projector is installed, if desired. The projector provides the following connection options: • M1-DA/DVI (Digital Visual Interface) • HDMI™ (High Definition Multimedia Interface) • Compo...

5 Positioning the projector To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some guidelines: • Position the projector on a flat surface at a r...

6 Choosing the aspect ratio Aspect ratio is the ratio of the image width to image height. HDTV and most DVDs are 16:9, which is the default for this projector. When in 4:3 mode the pro-jector places black bars on both sides of the image. Native mode centers the image and turns off the internal scale...

7 Connecting a video device You can connect video devices such as HDTV receivers, HD-DVD players, VCRs, camcorders, digital cameras, video game consoles, and TV tuners to the projector. Connect the audio from your video device to your stereo system to get sound. You can connect the projector to most...

8 HDMI 1.3 connection HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI pro-vides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video-out connector on the video device and into the HDMI connecto...

9 Displaying an image Connect the power cord to the Power connector on the back of the projector and to your electrical outlet. NOTE : Always use the power cord that shipped with the projector. Press the Power button on the remote. The Power light on the Status Indicator Panel blinks green and the f...

11 Shutting down the projector Power Save The projector also has a Power Save feature that automatically turns the lamp off after no active sources are detected and no user interaction with the projector is performed for 20 minutes. By default, this feature is on. See page 24. Sleep Timer The projec...

14 image not sharp Adjust focus or adjust Sharpness in the Picture>Advanced menu correct image image upside down turn off ceiling in Settings>System menu correct image A B A B A B AB A B K1 RG.fm Page 14 Thursday, November 8, 2007 9:08 AM

15 image reversed left to right turn off rear in Settings>System menu correct image projected colors don’t match source adjust color, tint, color temperature, brightness, contrast in the menus. Verify cable connections. correct image lamp won’t turn on, Temperature light is on make sure vents are...

16 Still need assistance? If you need assistance, visit our website at www.infocus.com or call us. This prod-uct is backed by a limited warranty . An extended warranty plan may be purchased from your retailer or dealer. When sending the projector in for repair, we recommend shipping the unitin its o...

17 Using the remote control The remote uses two (2) AA batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover. To operate, point the remote at the projection screen or at the f...

18 Optimizing video images Your projector has been factory optimized for excellent performance no matter what the source. However, if you wish to make further changes you can optimize the image using onscreen menus. For general information on using the menus, see page 19. • Adjust the Keystone, Cont...

19 Using the menus To open the menus, press the Menu button on the remote. (The menus automat- ically close after 60 seconds if no buttons are pressed.) The Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button. To change a menu s...

23 Color Temperature : changes the intensity of the colors. Select a value. Native means an uncorrected/unchanged color temperature. Other values change the white point of the colors. 6500K (the default setting) is generally used for film con-tent and 9300K is used for TV video. Color Gamut : sets t...

27 Maintenance Replacing the projection lamp The lamp hours timer in the Service Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, a message appears on the screen at startup indicating that you should change the lamp. The LED on top of the proj...

29 Appendix Remote control discrete codes You can use these codes to program another remote to learn the projector’s remote functions. To activate discrete mode, press and hold the Custom button on the remote for 10 seconds. The back light blinks twice when discrete mode is entered. The remote butto...

30 Supported video formats Connector Signal Type Supported formats HDMI Digital RGB and YCrCb(HDCP or non-HDCP) 1080p/24Hz1080p/50Hz1080p/60Hz 1080i/50Hz/60Hz1080i/50Hz (Australia) 720p/50Hz/60Hz576i/p/50Hz/60Hz480i/p/50Hz/60Hz Digital RGB video via M1-to-DVI cable(HDCP or non-HDCP) Analog RGB video...

31 RS-232 terminal Product Interface specifications Communication configuration To control the projector from an LCD control panel, connect an RS-232 cable to the serial control connector on the projector and set your computer’s serial port settings to match this communication configuration: Command...

32 Supported commands Function Command Range Default Aspect Ratio ARZ 0-50 = Auto 1 = Native 2 = 4:3 3 = 16:9 4 = Letterbox 5 = Natural Wide 1 Auto Ceiling Enable ACL 0-1 0 Auto Color Gamut Enable AGA 0-1 1 Auto Color Space enable ACS 0-1 1 Auto Image AIM 0-1 0 Auto Power Enable APO 0-1 0 Auto Sourc...

36 INDEX Numerics 12 volt outputs 416x9 18 A Advanced menu 22aspect ratio 6, 20Auto Ceiling 24Auto Image 20Auto Power 24Autosource 24 B Black Level Calibration 22blank screen 25Brightness 20BrilliantColor 21 C cable box 7Ceiling 24CLI commands 32Color 20Color Control 23Color Gamut 23Color Space 22, ...