InFocus IN70 SERIES - Manuals

5 Adjust the picture Height 1 Keystone 2 Zoom and focus 3 Aspect ratio 4 zoom(outer ring) focus(inner ring) Tilt the projector up or down. Press menu (on projector or remote). Press or to highlight Picture , then press select . Press or to highlight Keystone , then press select . Press or to adjust ...

6 Turn off the projector 7 It’s quick, easy, and secure. Activate your warranty to ensure eligibility for service and support. Get special offers and notifications about free product updates. Write down your projector’s serial number It’s printed on the label on the back of the projector. You’ll nee...

Troubleshooting There is no picture or the image is blank The picture is unstable or distorted,or “Signal out of range” is displayed Check power If the light on the projector near the power button is off, make sure the power cord is connected and plugged into a working electrical outlet. If the ligh...

1 Declaration of Conformity Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands We declare under our sole responsibility that this projector conform to the following directives and norms: EMC ...

2 Table of Contents Introduction 3Positioning the projector 5 Choosing the aspect ratio 6 Video connectors 7 Connecting a video device 8 Composite (RCA) video connection 8 S-video connection 8 Component (RCA) connection 8 SCART RGB connection 8 Digital connections 9 DVI connection 9 HDMI connection ...

3 Introduction Your new InFocus projector is specifically designed for home theater appli- cations. It sets a high standard using the latest DLP™ technology and new DNX video processing from Pixelworks™. Whether you are watching mov-ies or High Definition broadcasts or playing the latest video game,...

4 Connector Panel The projector provides the following connection options: • M1-DA/DVI (Digital Visual Interface) • HDMI™ (High Definition Multimedia Interface) • Component (RCA) • SCART RGB (you must enable this connector, see page 26) • S-video • Composite video (RCA) See “Video connectors” on pag...

5 Positioning the projector To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some guidelines: • Position the projector on a flat surface at a r...

6 Choosing the aspect ratio Aspect ratio is the ratio of the image width to image height. HDTV and most DVDs are 16:9, which is the default for this projector. When in 4:3 mode the projector places black bars on both sides of the image. Native mode centers the image and turns off the internal scaler...

7 Video connectors The first step for connecting video is determining what type of output con-nectors your video device has. If there is more than one output, select the one with the highest quality. The best quality ranking, with 1 being the highest, is: 1 M1-DA/DVI or HDMI (both are digital inputs...

8 Connecting a video device You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. Connect the audio from your video device to your stereo system to get sound. You can connect the projector to most vi...

9 Digital connections The M1-DA/DVI and HDMI (High-Definition Multimedia Interface) con-nectors are digital and yield the highest quality image. It is common for these signals to be encrypted with HDCP (high-bandwidth digital-content protection). Your new projector ships standard with decryption cod...

10 Displaying an image Connect the power cord to the Power connector on the back of the projector and to your electrical outlet. NOTE : Always use the power cord that shipped with the projector. Press the Power button on the remote or keypad. The LED flashes green and the fans start to run. When the...

12 Shutting down the projector Power Save The projector also has a Power Save feature that automatically turns the lamp off after no active sources are detected and no user interaction with the projector is performed for 20 minutes. By default, this feature is on. See page 26. Sleep Timer The projec...

15 image not sharp adjust Sharpness in the Picture>Advanced menu correct image image upside down turn off ceiling in Settings>System menu correct image A B A B A B AB A B

16 image reversed left to right turn off rear in Settings>System menu correct image projected colors don’t match source adjust color, tint, color temperature, brightness, contrast in the menus correct image lamp won’t turn on, LED blinking red make sure vents aren’t blocked, turn off the projecto...

18 Using the remote control The remote uses two (2) provided AA batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + and - ends of the bat-teries, sliding them into place, and then replacing the cover. To operate, point the remote at the projection screen o...

19 Using the keypad buttons Most buttons are described in detail in other sections, but here is an over-view of their functions: Menu –opens the on-screen menus (page 21). Select –confirms choices made in the menus (page 21). Up/Down arrows –navigates to and adjusts settings in the menus (page 21). ...

20 Optimizing video images Your projector has been factory optimized for very good performance no matter what the source. However, if you wish to make further changes you can optimize the image using onscreen menus. For general information on using the menus, see page 21. • Adjust the Keystone, Cont...

21 Using the menus To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) The Main menu appears. Use the arrow buttons to move up and down to high-light the desired submenu, then press the Select button. To change...

29 Maintenance Cleaning the lens 1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth. • Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2 Lightly wipe the cleaning c...

32 Appendix Red LED behavior and projector errors If the projector is not functioning properly and the LED is blinking red, con-sult Table 4 to determine a possible cause. There are two-second pauses between the blinking cycles. Visit our website for more details on the red LED error codes. Table 4:...

33 Remote control discrete codes You can use these codes to program another remote to learn the projector ’s remote functions. To activate discrete mode, press and hold the Custom button on the remote for 10 seconds. The back light blinks twice when discrete mode is entered. The remote buttons are n...

34 Projector dimensions for ceiling mount installations All values in millimeters (mm). 234.5 126.5 361 121 40.25 57 64 344.25 167 40.5 24.5 163 227.5 245.5

35 Supported video formats Connector Signal Type Supported formats HDMI Digital RGB and YCrCb(HDCP or non-HDCP) 480i/p/50Hz/60Hz576i/p/50Hz/60Hz720p/50Hz/60Hz1080i/50Hz/60Hz1080i/50Hz (Australia)1080p/24Hz (IN76/78 only) 1080p/50Hz1080p/60Hz Digital RGB video via M1-to-DVI cable(HDCP or non-HDCP) An...

37 Supported commands Function Command Range Default Auto Ceiling Enable ACL 0-1 0 Auto Color Space enable ACS 0-1 1 Auto Image AIM 0-1 0 Aspect Ratio ARZ 0-40 = Native1 = 4:3 2 = 16:93 = Letterbox4 = Natural Wide 1 Auto Power Enable APO 0-1 0 Auto Source Enable ASC 0-1 1 Auto Video Standard Enable ...