IBM ETX-DB-ATX - Manuals - manualsarea.com

Page 2 - Introduction

ETX-DB-ATX 3 3.16 PCI BUS Interface ................................................................. 20 3.17 ISA BUS Interface ................................................................. 22 3.18 ATX power connector ............................................................ 23 3.19 Front Pan...

Page 3 - Installation; This chapter gives instructions about how to set up the

ETX-DB-ATX 5 * ISA interface: One ISA slots. * 10/100Mbps Ethernet Controller: Intel 82551QM or Realtek RTL8100 IEEE802.u 100 BASE-TX standard Dual Auto-sensing interface to 10MBps or 100MBps networks. On board RJ45 connectors provide for easy connection. * Power connector: standard ATX power connec...

Page 4 - Unpacking Precautions; JP4 DESCRIPTION; Clear CMOS Setup

ETX-DB-ATX 7 ETX-DB-ATX Layout CN16 A T X PWER JP7 Battery ISA1 CN9 JP6 Digital IO PSLOT2 PSLOT1 X1 X2 CN1 CN10 CN20 CN13 CN14 CN3 USB3 ET X-D B -A T X V1 .2 COM2 CN1 1 X3 X4 CN2 CN8 CN5 CN6 CN12 JP4 CN15 IR CN4 CN7 CN21 USB2 KB/MS USB COM1 LPT1 VGA AUDIO 48 BIT LVDS CN17 JP10 ETX-DB-ATX 8 2.2 Unpac...

Page 5 - WatchDog Timeout Active Selector; JP7: WatchDog Active Select; Ethernet Controller Setting; Connection; This chapter describes how to connect peripherals, switches; ETX Connector X1

ETX-DB-ATX 9 2.5 WatchDog Timeout Active Selector Reading I/O port 443H enables the WatchDog Timer. It should be triggered before the time-out period ends, otherwise it will assume the program operation is abnormal and will issue a reset signal or an interrupt signal. The Watch-Dog Timer is disabled...

Page 6 - ETX Connector X2; ETX Connector X3; and Keyboard

ETX-DB-ATX 11 3.2 ETX Connector X2 X2: ISA Bus PIN SIGNAL PIN SIGNAL PIN SIGNAL PIN SIGNAL 1 GND 2 GND 51 5V 52 5V 3 SD!4 4 SD15 53 SA6 54 IRQ5 5 SD13 6 MASTER# 55 SA7 56 IRQ6 7 SD12 8 DRQ7 57 SA8 58 IRQ7 9 SD11 10 DACK7# 59 SA9 60 SYSCLK 11 SD10 12 DRQ6 61 SA10 62 REFSH# 13 SD9 14 DACK6# 63 SA11 64...

Page 7 - ETX Connector X4; PIN SIGNAL; Floppy Disk Drive Connector; PIN

ETX-DB-ATX 13 3.4 ETX Connector X4 X4: IDE1, IDE2, and Miscellaneous PIN SIGNAL PIN SIGNAL PIN SIGNAL PIN SIGNAL 1 GND 2 GND 51 SIED_ IOW# 52 PIDE_ IOR# 3 5VSB 4 PWGIN 53 SIDE_DRQ 54 PIDE_ IOW# 5 PS_ON 6 SPEAKER 55 SIDE_D15 56 PIDE_DRQ 7 PWRBTN# 8 VBAT 57 SIDE_D0 58 PIDE_D15 9 KBINH 10 N.C. 59 SIDE_...

Page 8 - CN14: 40-pin Secondly IDE Interface Connector

ETX-DB-ATX 15 3.6 PCI E-IDE Disk Drive Connector For IDE HDD connection, The ETX-DB-ATX was designed with two 2.54mm standard IDE connector (CN13, CN14) CN13: 40-pin Primary IDE Interface Connector CN14: 40-pin Secondly IDE Interface Connector PIN NO. DESCRIPTIO N PIN NO. DESCRIPTIO N 1 RESET# 2 GRO...

Page 9 - DESCRIPTION; USB Port Connector; CN5: External USB Connector; IrDA Infrared Interface Port; CN16: IrDA connector; VGA Connector

ETX-DB-ATX 17 assignment of the connectors are specified as following tables: • CN9: Serial Port1 Connector (9-pin D-sub) PIN NO. DESCRIPTION 1 DATA CARRIER DETECT (DCD) 2 RECEIVE DATA (RXD) 3 TRANSMIT DATA (TXD) 4 DATA TERMINAL READY (DTR) 5 GROUND (G ND) 6 DATA SET READY (DSR) 7 REQ UEST TO SEND (...

Page 10 - PSLOT1: PCI Slot 1; PCI Routing List; SIGNAL

ETX-DB-ATX 19 9 NC 10 GROUND 11 NC 12 DDC DAT 13 HSY NC 14 VSYNC 15 DDCCLK 3.13 LCD/LVDS Interface Connector The ETX-DB-ATX provides one 30-pin connector for the LVDS flat panel interface. • CN12: Two channel 48 bits LVDS Interface Connector PIN NO. Description PIN NO. Description 1 GND 2 GND 3 TxO ...

Page 11 - ISA BUS Interface

ETX-DB-ATX 21 • PSLOT1~PSLOT2: PCI Bus pin assignment A B NO. Signal NO. Signal NO. Signal NO. Single 1 N.C. 2 +12V 1 -12V 2 N.C. 3 N.C. 4 N.C. 3 GND 4 N.C. 5 +5V 6 INTA# 5 +5V 6 +5V 7 INTC# 8 +5V 7 INTB# 8 INTD# 9 N.C. 10 +5V 9 N.C. 10 N.C. 11 N.C. 12 GND 11 N.C. 12 GND 13 GND 14 N.C. 13 GND 14 N.C...