Hyundai H-CDM8045 - Manuals

Hyundai H-CDM8045 Car Radio – User Manual in PDF format online.

Manuals:

User Manual

User Manual Hyundai H-CDM8045

Summary

Page 2 - Table of contents

2 Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefullybefore connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents .....................................

Page 3 - Important safeguards; BEFORE USING

3 Important safeguards Using the device at temperature below -10º may cause the breakage of the device. BEFORE USING PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED TEMPERATURE! Read carefully through this manual to familiarize yourself with this high-quality sound system. Disconnect the...

Page 4 - Installation/ connection; Insert fingers into the groove in the front of frame and remove it.; Removing the unit

4 Installation/ connection Attention: REMOVE THE TRANSPORT CD STOPPER (2 SCREWS)BEFORE USE. Din front-mount (method 1) After inserting the holder into the dashboard, select the appropriatetab and bend them inwards to secure the holder in place. Insert fingers into the groove in the front of frame an...

Page 5 - Install the front panel

5 Din rear-mount (method 2) Installation using the screw holes at both sides of the unit.1. Select a position where the screw holes of the main unit are fitted for aligned, and tighten the screws at 2 positions at each sides.Use either truss screws (5 x 8mm) or flush surface screws (4 x 8mm), depend...

Page 7 - Using the ISO Connector

7 Do not interchange the connection of the wiring!!!For some car models you may need to modify wiring of the supplied power cord. Contact your authorized cardealer before installing this unit. Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISOconnectors a...

Page 8 - Panel controls; Front panel; Press it to display current mode.

8 Panel controls Front panel 1. POWER button Press POWER button to turn the power on, press again to turn the power off. 2. DISP button Press it to display current mode. 3. VOLUME knob/ SEL button Rotate VOL button clockwise to increase the volume level; rotate anticlockwise to decrease the volumele...

Page 10 - Back of the front panel; Disc slot: insert a disc for playback here

10 Back of the front panel Press the REL button to open the panel and press EJECT button to eject the disc. Note: Pressing the RESET hole will erase the clock setting and stored stations. Panel status indicator lights up when you slide the panel down; flashes when you remove the panel. Disc slot: in...

Page 11 - Remote control; Press to select your desired modes.

11 Remote control 1. MOD button Press to select your desired modes. 2. SEL/ MENU button Repeatedly press SEL/MENU to select modes.During disc playback, press it to display the root menu of thedisc. 3. BAND button During radio mode, press to select bands. 4. TA buttonPress it to activate the traffic ...

Page 13 - Changing the battery; Press the catch and at the same time pull out the battery tray.

13 Changing the battery 1. Press the catch and at the same time pull out the battery tray. 2. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facingupward. Insert the battery tray into the remote control. Warning: Store the battery where children cannot reach. If a ...

Page 14 - General operation; Reset the unit; to restore the unit; Power button; PWR; Volume control; Volume adjust

14 General operation Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press REL button on the panel to open the panel and press the RESET hole with a point object to restore the unit to the original factory settings. Power button Press...

Page 15 - Setting other characteristics; Press the VOLUME ( , ) buttons on the RC or rotate the VOLUME

15 If you don t adjust VOL buttons within 3 seconds after selecting the desired mode, the unit will automaticallyreturn to the current mode being displayed. When EQ mode is activated, press SEL button to select modes: VOL/ BAL/ FAD.BAS/ TRE are invalid. Setting other characteristics During FM mode, ...

Page 17 - buttons on the RC to adjust

17 station is received. - SEEK2: Press the Tuning up/ down button briefly to increase or decrease the frequency by 1 step size. Press and hold the Tuning up/ down button increase or decrease the frequency rapidly until the button isreleased, the different between the same operation at Seek 1 mode is...

Page 18 - Mode setting

18 Mode setting Press the MOD button on the RC or MODE button on the panel to select TUNER, S-CDP (single disc playback),USB DRIV modes.If you select TUNER mode, press BAND once or more to select FM1, FM2, FM3, FM4 (OIRT), AM1, AM2.

Page 19 - Digital tuner; Band selection; buttons

19 Digital tuner Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. Band selection Press POWER to power on, then press the MOD button on the RC or MODE button on the pane...

Page 21 - This function is also valid during playback mode.

21 PTY (Program Type) function Press PTY button, if no other button is pressed in 10 seconds, the unit will begin to search the program youreceived last time.If no program is received, LCD displays NO PTY.Press PTY the first time, then press the number buttons, you can select the music program style...

Page 22 - or

22 CD/ MP3/ USB operations Loading a disc 1. Press REL button on the panel to slide down the panel. Insert the disc with the printed side facing upward into the slot. 2. Press REL button to slide down the panel. Press EJECT button on the panel to eject the disc. Playing a disc When the disc has been...

Page 23 - buttons on the RC or; Random playback; Press again to select the current track.

23 Repeat playing Press the RPT button on the panel or RC to repeat current track. Press it again to cancel the function.The default setting is DISC REPEAT. Inserting the number of track Press the number buttons on the RC or on the panel to input the desired tracks. Use the 5 button to go backward t...

Page 24 - Search function; Track search; Press until the required track will be blinking on LCD.

24 Search function During MP3/USB mode, searching tracks can be achieved through track search, file search and character searchby using (SEL) button, (AMS) button and Track search For example: Find the track NO.131 on the disc:1. Press AMS button once to enter the initial searching mode, LCD shows T...

Page 25 - Character search; Press SEL button until LCD shows required word.; Finish working with USB; Fit on the harness rubber after exiting the USB.

25 Character search 1. Press AMS button three times, LCD shows CHAR SCH.2. Press SEL button to enter into character searching mode. LCD shows blinking A button.3. Press SEL until required letter blinking on LCD.4. Press SEL button to enter into selected folder files. The display will show CA, A is t...

Page 27 - Handling discs; Dirty, scratched or warped discs may cause skip ping or noise.; Cleaning; Cleaning the cabinet

27 Handling discs Dirty, scratched or warped discs may cause skip ping or noise. Handle the disc only by the edges. To keep clean do not touch its surface. Discs should be stored in their cases after use to avoid scratches. Do not expose discs to direct sunlight, high humidity, high temperature or d...

Page 28 - Troubleshooting guide; Symptom

28 Troubleshooting guide Symptom Cause Solution GeneralNo power The car ignition is not on.The fuse is blown. If the power supply is properly connected to the caraccessory switch the ignition key to ACC .Replace the fuse. DiscDisc cannot be loaded. Presence of disc inside the player. Remove the disc...

Page 29 - Specification; Maximum power output:; Audio Specification; Maximum Output

29 Specification Specifications are subject to change without notice. Mass and dimension are approximate. General. Power supply: 14.4V DC Current consumption/Fuse: max. 15A/ 15 A Maximum power output: 50Wx4 channels Dimensions (W x H x D) 178 x 50 x 192 mm Working temperature range: -10º - +60º FM S...

Page 32 - CD

32 / : CD . , , , . 1. 2. (5 ) 3. 4. (5 x 25 ) 5. 6. 7. . ( .) , , , , . , , .

Page 35 - ISO

35 !!! . . ISO 1. ISO, , . 2. ISO , . , . A B 1 (+)--- 2 (-)--- 3 (+)--- 4 12 (+)/ (-)--- 5 / (+)--- 6 ((-)--- 7 ACC+/ (+)--- 8 (-)---

Page 51 - Intro; INT

51 / / , . : , , . R , . . . 5 . , 32, 5, 30. 6 . , 32, 6, 40. / / , 1 . Intro VCD/ CD/ MP3 . 10 . 1. INT . . 2. INT , .

Page 53 - USB

53 4. SEL, . , ( ) . ( SEL, 1 ) 5. SEL, . 6. SEL. . : AMS, SEL . , . USB USB , . USB CD/ MP3 , . : USB .