Honda 90501 898 000 - Manuals

Page 2 - IMPORTANCE OF PROPER SETUP AND PRE-DELIVERY SERVICE; FOR YOUR CUSTOMER’S SAFETY; do otherwise. This will help eliminate several potential hazards:; WARNING

HS928K1 • HS1332 SNOWBLOWERS 2 of 13 IMPORTANCE OF PROPER SETUP AND PRE-DELIVERY SERVICE FOR YOUR CUSTOMER’S SAFETY Proper setup and pre-delivery service are essential to the customer’s safety and the reliability of the snowblower. Any error or oversight made during assembly and servicing of a snowb...

Page 3 - FOLLOW THESE INSTRUCTIONS CAREFULLY; Power Equipment Pre-Delivery Check List; NUT AND BOLT DIAMETER; mm flange bolts; How to measure hardware and components:

HS928K1 • HS1332 SNOWBLOWERS 3 of 13 Torque values for special hardware will be called out during the procedure. Setup and pre-delivery service must be performed by an authorized Honda snowblower dealer. These instructions are provided for dealer use. FOLLOW THESE INSTRUCTIONS CAREFULLY Proper setup...

Page 4 - LOOSE PARTS; Remove the crate cover and open the parts carton.; Description

HS928K1 • HS1332 SNOWBLOWERS 4 of 13 LOOSE PARTS Remove the crate cover and open the parts carton. Remove all the parts from the carton. Check the parts against these illustrations. Description Quantity Part Number Illustration Owner’s manual 1 31V416000 Tool Kit (contains spark plug wrench & ha...

Page 6 - DAMAGE OR MISSING PARTS; Warranty Policy and Procedures Manual; UNCRATING; HANDLE INSTALLATION

HS928K1 • HS1332 SNOWBLOWERS 6 of 13 DAMAGE OR MISSING PARTS • For parts lost or damaged in transit, refer to section 3 of the Warranty Policy and Procedures Manual . • For parts left out by the factory, refer to section 6 of the Warranty Policy and Procedures Manual . UNCRATING 1. Remove and discar...

Page 7 - WIRE BAND INSTALLATION; Left side; LEFT SIDE

HS928K1 • HS1332 SNOWBLOWERS 7 of 13 • Wheel-Type 1. Install the lower handle cap.2. Set the handle and install the four handle holder bolts. • Route the choke cable outside the handle. • Route the other cables and code inside the handle. 3. Install the four joint washers and tighten the four nuts. ...

Page 9 - WITHOUT ENGINE

HS928K1 • HS1332 SNOWBLOWERS 9 of 13 ADJUSTMENTS 1. Check the backlash between the chute drive gear and driven gear. Adjust as necessary. BACKLASH: 0.5 ~ 1.0 mm (0.02 ~ 0.04 in) 2. Check that the chute rotates smoothly when the chute handle is operated. If the chute handle does not rotate smoothly, ...

Page 10 - NOTICE

HS928K1 • HS1332 SNOWBLOWERS 10 of 13 2. Check the hydrostatic transmission fluid level while the engine is cold. If necessary, fill the transmission reservoir to the temperature compensated level shown in the following table by removing the reservoir cap and cup. Use only Honda Hydrostatic Fluid. P...

Page 11 - SCRAPER BAR GROUND CLEARANCE; Ordinary surfaces

HS928K1 • HS1332 SNOWBLOWERS 11 of 13 7. Check the scraper bar and skid shoe adjustments: The skid shoes can be mounted on the front of the auger housing (front mount) or on the rear of the auger housing (rear mount). The rear-mount skid shoe adjustment is shown. The front-mount skid shoe adjustment...

Page 12 - OPERATIONAL TESTS; CORRECT TRACK DEFLECTION

HS928K1 • HS1332 SNOWBLOWERS 12 of 13 8. On Track-types: Check track tension. a. With the snowblower resting on its tracks, check track deflection by pressing down midway between the wheels with a force of 15 kg (33 Ib). b. Adjust if necessary. Be sure to adjust both sides evenly. 9. Check the secur...

Page 13 - yellow copy to the customer.

HS928K1 • HS1332 SNOWBLOWERS 13 of 13 13.Fill out the appropriate areas of the Power Equipment Pre-Delivery Check List (TO056), and give the yellow copy to the customer. PRE-DELIVERY (PDI) CHECK LIST The following pre-delivery (PDI) check list is designed for general application. There are individua...