Heat & Glo Cosmo-130 - Manuals

Page 2 - Listing Label Information/Location; Owner’s Manual; Homeowner Reference Information; NA; Read this manual before installing or operating this appliance.

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on ﬁ replace: __________________...

Page 3 - Safety Alert Key:; Used to address practices not related to personal injury.; Table of Contents; User Guide

3 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • CAUTI...

Page 4 - B. Limited Lifetime Warranty

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 4 B. Limited Lifetime Warranty

Page 6 - Models; NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.; Listing and Code Approvals; Standard Test Method for Behavior of Materials in a

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 6 C. BTU Speciﬁ cations MODELS: Cosmo-I30, Cosmo-I35 LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Vented Gas Fireplace Heater STANDARD: ANSI Z21.88-2009 CSA 2.33-2009 Vented Gas Fireplace Heaters This product is listed to ANSI ...

Page 7 - Operating Instructions; WARNING! DO NOT operate fi; A. Gas Fireplace Safety; WARNING; HOT SURFACES; Keep media out of reach

7 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 2 Operating Instructions Figure 2.1 General Operating Parts B. Your Fireplace WARNING! DO NOT operate ﬁ replace before read- ing and understanding operating instructions. Failure to operate ﬁ replace according to operating instructions...

Page 8 - E. Fixed Glass Assembly; barrier to prevent direct contact with the; F. Remote Controls, Wall Controls and Wall; G. IPI Battery Tray/Battery Installation

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 8 C. Clear Space WARNING! DO NOT place combustible objects in front of the ﬁ replace or block louvers. High temperatures may start a ﬁ re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat m...

Page 9 - I. Before Lighting Fireplace; have a; H. Control Module Operation; Module Reset

9 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 I. Before Lighting Fireplace Before operating this ﬁ replace for the ﬁ rst time, have a qualiﬁ ed technician : • Verify all shipping materials have been removed from inside and/or underneath the ﬁ rebox. • Review proper placement of lo...

Page 10 - tery life, remove them when using the transformer.; LIGHTING; NOT FOR USE; GAS; WHAT TO DO IF YOU SMELL GAS; DO NOT CONNECT LINE VOLT-; Also Certifi ed for Installation in a; Final inspection by

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 10 J. Lighting Instructions (IPI) The IPI system may be operated with four AA-cell batteries. When using batteries, unplug the transformer. To prolong bat- tery life, remove them when using the transformer. 1. This appliance is equipped ...

Page 11 - K. After Appliance is Lit; ISSUE

11 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 Initial Break-in Procedure• The appliance should be run three to four hours continuously on high. • Turn the appliance off and allow it to completely cool.• Remove ﬁ xed glass assembly. See Section 12.F.• Clean ﬁ xed glass assembly. S...

Page 12 - Glass Cleaning; Tools Needed; CAUTION! Handle fi xed glass assembly with care.; Note; Maintenance and Service; The appliance should be; Tools needed; Remote Control

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 12 Glass Cleaning Frequency: Seasonally By: Homeowner Tools Needed : Protective gloves, glass cleaner, drop cloth and a stable work surface. CAUTION! Handle ﬁ xed glass assembly with care. Glass is breakable. • Avoid striking, scratching...

Page 14 - Burner Ignition and Operation

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 14 Burner Ignition and Operation Frequency: Annually By: Service Technician Tools needed: Protective gloves, vacuum cleaner, whisk broom, ﬂ ashlight, voltmeter, indexed drill bit set, and a manometer.• Verify burner is properly secured a...

Page 15 - A. Typical Appliance System; Illustrations and photos re; Getting Started; Installer Guide

15 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 A. Typical Appliance System NOTICE: Illustrations and photos re ﬂ ect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual VERTICAL TERM...

Page 16 - Read all of the instructions before starting the instal-; C. Tools and Supplies Needed; Any such action may cause a fi re hazard.; DO NOT use this appliance if any part has been under

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 16 B. Design and Installation Considerations Heat & Glo gas inserts are designed for installations into solid fuel masonry or factory built ﬁ replaces that have been installed in accordance with the National, Provin- cial, State and ...

Page 17 - Fireplace Size Requirements; A. Minimum Fireplace Opening; Provide adequate

17 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 5 Fireplace Size Requirements Figure 5.1 Fireplace Opening In addition to these dimensions, also reference Clearances and Mantel Projections (Section 5.B). E D C I B A G H F MINIMUM FIREPLACE SIZE Location COSMO-I35 COSMO-I30 Inches M...

Page 18 - B. Mantel and Wall Projections; • Use leveling legs to raise insert minimum 1/4 inch (6 mm); TOP VIEW

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 18 B. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci ﬁ ed. Framing or ﬁ nishing material closer than the minimums listed must be construct- ed entirely of noncombustible m...

Page 19 - A. Vent Termination Minimum Clearances; Termination Locations; DO NOT

19 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 A. Vent Termination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/12 to 8/12 .......

Page 20 - Installation Preparation; A. Inspection and Cleaning

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 20 7 Installation Preparation Prepare the existing solid fuel masonry or factory built non-combustible ﬁ rebox for installation. A. Inspection and Cleaning Prior to installing the gas insert:• Have the chimney and adjacent structure insp...

Page 21 - B. Venting Components; Installing Vent Pipe and Appliance; C. Connecting Vent Pipe; • May impair safe operation of this appliance or other; Description; CAUTION! ALL vent specifi cations MUST be followed.

21 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 B. Venting Components CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. The vertical vent termination system installed on this model includes:•...

Page 22 - ance; • Connect exhaust vent pipe ONLY to exhaust starting

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 22 Figure 8.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • Trim chimney top plate to minimize excess overhang or bend over ﬂ ue tile (see Figure 8.2). • Place 3/8 inch bead of 300º F silicone on ﬂ ue tile top. D. Pla...

Page 23 - F. Installing Adaptor and Termination Cap; For installation of termination cap see minimum vent; Wear protective gloves and safety glasses during instal-; Damper Flashing Kit; : Damper may have to be removed to use this kit.; Masonry; OR; To help eliminate cold air drafts, it may be necessary to place non-; system REQUIRES this insulation.

23 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 F. Installing Adaptor and Termination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 8.4) . To install adaptor see Figure 8.5. Roof Pitch H (Min.) Ft.Flat to 6/12...................

Page 24 - Gas Information; • If substituting for these components, please consult; D. High Altitude Installations; Gas Pressure

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 24 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualiﬁ ed technician (NFI certiﬁ ed or factory-trained) using Hearth & Home Technologies speciﬁ ed and approved p...

Page 25 - A. Wiring Requirements; National Electric Code; Electrical Information; B. IntelliFire PlusTM Ignition System Wiring; WARNING! Risk of Shock or Explosion! DO NOT

25 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric C...

Page 26 - C. Optional Accessories Requirements; Label all wires prior to dis-

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 26 Figure 10.2 Fan Wiring Diagram BLOWERS BLOWER RECEPTACLE BLKGRNBLK BLKGRNBLK WHT GRN BLK BLK GRN WHT BLK BLK BLK BLK PLUG INTO 120V EXISTING OUTLET TEMPERATURE SENSOR SWITCH VARIABLE SPEED CONTROL DC REGULATOR RECEPTACLE JUMPER WIRE P...

Page 27 - D. Fan Wiring with Remote; This appliance may be used with an RC200 or RC300; E. Control Module Operation; See Section 2.H for control module operation instructions.

27 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 PLUG 120V EXISTING OUTLET GRN (2) BLK (2) BLK (2) GRN (2) BLK (2) STEPS 3 & 4 WHT (2) BLOWER SPEED CONTROL (RHEOSTAT) SENSOR SWITCH STEPS 1 & 2 STEP 5 BLOWERS BLOWER RECEPTICLE BLKGRN BLK BLKGRN BLK WHT GRN BLK BLK GRN WHT BLK...

Page 28 - Finishing; A. Mantel and Wall Projections

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 28 11 Finishing A. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci ﬁ ed. Framing or ﬁ nishing material closer than the minimums listed must be construct- ed entirely of non...

Page 29 - WARNING! Risk of Fire and Electric Shock!; Appliance Setup; E. Glass Panel Instructions

29 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 A. Remove Glass Assembly See Section 12.F. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the ﬁ rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the ﬁ rebox ...

Page 30 - G. Air Shutter Setting; F. Fixed Glass Assembly; DO NOT operate; Removing Fixed Glass Assembly; Air Shutter Settings; NG

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 30 G. Air Shutter Setting Air shutter settings should be adjusted by a qualiﬁ ed ser- vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertica...

Page 31 - Troubleshooting; arrange a service call by a qualifi ed technician.; A. IntelliFire PlusTM Ignition System; Symptom

31 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 13 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualiﬁ ed technician in th...

Page 32 - IntelliFire PlusTM Ignition System

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 32 IntelliFire Plus™ Ignition System (continued) Symptom Possible Cause Corrective Action 4. Pilot lights but con- tinues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot ﬂ ame has been lit, ﬂ a...

Page 33 - Reference Materials; A. Appliance Dimension Diagram

33 Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 14 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. Figure 14.1 Appliance Dimensions A H B C D E I G F N M L K J O R Q P S GAS LINE ACCESS ELECTRICAL ACCESS T MODEL...

Page 34 - B. Vent Kits Components; GK to connect collinear fl ex vent to SL-D vent pipe to

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 34 B. Vent Kits Components Direct Vent Flex Liner Kits (see Figure 14.2)LINK-DV-30B or (LINK-DV-30): Masonry 3 inch ﬂ ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, ﬂ ashing, and link adapter.LINK-DV4-30B or (LI...

Page 35 - D. Contact Information; For the location of your nearest Heat & Glo dealer,; DO NOT DISCARD THIS MANUAL; NOTICE

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11 40 Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215 th Street West, Lakeville, MN 55044 www.heatnglo.com D. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For the loca...