Page 2 - CONTENTS; DISASSEMBLY INSTRUCTIONS
—2— CONTENTS 1. PREFACE ...................................................................................................................................................3 1.1 FEATURES......................................................................................................................
Page 5 - MECHANICAL PARTS; Figure 1
—5— 2. DISASSEMBLY INSTRUCTIONS 2.1 MECHANICAL PARTS 2.1.1 FRONT GRILLE 1. Pull the inlet grille forward. 2. Remove the screw securing the Front Grille. (Fig. 3) 3. Push the grille up from the bottom and pull the top of the grille away from the case to lift the top tabs out of their slots. (Fig. 4) ...
Page 6 - AIR HANDLING PARTS; Figure 6
—6— 2.2 AIR HANDLING PARTS 2.2.1 AIR GUIDE UPPER 1. Disconnect the unit from the power source.2. Remove the front grille. (Refer to Section 2.1.1)3. Remove the cabinet. (Refer to Section 2.1.2)4. Remove the control board. (Refer to Section 2.1.3) 5. Remove 2 screws that secure the air guide upper to...
Page 9 - Remove a screw securing the clip with cord to the; REFRIGERANT CYCLE
—9— 2.3.6 POWER CORD 1. Disconnect the unit from source of power.2. Remove the front grille. (Refer to Section 2.1.1)3. Remove the cabinet. (Refer to Section 2.1.2)4. Remove a screw that secures control board to base pan. (Refer to Section 2.1.3) 5. Pulls the control board toward you.6. Disconnect t...
Page 10 - NOTES
2.4.2 EVAPORATOR 1. Remove the cabinet.2. Discharge the refrigerant by using a refrigerant recovery system. 3. Remove the air guide upper. (Refer to Section 2.2.1) 4. After discharging the refrigerant completely, unbraze the interconnecting tube at the condenser connections. 5. Remove the evaporator...
Page 11 - Figure 21A-Pulling Vacuum
—11— Equipment needed: Vacuum pump, charging cylinder, manifold gauge, brazing equipment, pinch-off tool capableof making a vapor proof seal, leak detector, tubing cutter, hand tools to remove components and service valve. B A B A B A COMPOUND GAUGE SEE INSETS BELOW CAPILLARY TUBE EVAPORATOR(LOW PRE...
Page 12 - SELECT THE BEST LOCATION; NOTE: All supporting parts should be secured to firm
—12— 3. INSTALLATION This air conditioner is designed with a button-downchassis so it can be easily installed in a window. 3.1 SELECT THE BEST LOCATION 1. To prevent vibration and noise, make sure the unit is installed securely and firmly. 2. Install the unit where the sun does not shine directly on...
Page 13 - Installation; Insert the guide panels into the guides of the air condi-; LOCATING UNIT IN WINDOW; b. The bracket helps to hold unit securely in place. Be; CAUTION
—13— Installation 3.2.2 BEFORE INSTALLATION 1. Insert the guide panels into the guides of the air condi- tioner. Fasten the curtains to the unit with screws (TYPEA) as shown Figure. 25. 2. Cut the adhesive-backed seal strip (TYPE D) to the window width. Remove the backing from the seal strip and att...
Page 15 - REMOVAL FROM WINDOW; TROUBLESHOOTING GUIDE
—15— REMOVAL FROM WINDOW Turn the air conditioner off, disconnect the power cord, remove the L bracket and the screws installed through the top and bot-tom of the guide panels, and save for reinstallation later. Close the guide panels. Keeping a firm grip on the air conditioner,raise the sash, and c...
Page 17 - TROUBLESHOOTING GUIDE; Unit is running but cooling is ineffective.; Ineffective Cooling
—17— 4.3 TROUBLESHOOTING GUIDE In general, possible trouble is classified in two kinds. The one is called Starting Failure which is caused by an electrical defect. The other is Ineffective Air Con-ditioning caused by a defect in the refrigeration circuit and improper application. Unit is running but...
Page 18 - Fails to Start
—18— Fails to Start Improper thermostat setting Loose terminal connection Improper wiring Check of power source. Drop of power voltage. Capacitor check. Replacement. Check of control switch setting. Compressor fails only to start. Defect of compressor capacitor. Replacement of compressor (Motor dama...
Page 22 - PER SET
—22— 5. CIRCUIT DIAGRAM 1 2 6 7 5 3854AR2330A COMP. MOTOR ROCKER SWITCH YL BR THERMOSTAT OLP BR R BL RD BK OR(BR) CAPACITOR F H C YL ROTARY SWITCH 2 H L M BK BR RD BL BK POWER INPUT BK(BR) (Plain) WH(BL) (Ribbed) GN(GN/YL) RD BL YL OR(BR) 4 6 8 1 3 5 7 BL RD BK BR WIRING DIAGRAM SYNC. M. S C 3 4 Q'T...
Page 25 - 828A26005D
6SHFLILFDWLRQVDQGSHUIRUPDQFHGDWDVXEMHFWWRFKDQJHZLWKRXWQRWLFH +($7&21752//(5,1& :(//:257+$9(18(-$&.6210,&+,*$1 7+(48$/,7</($'(5,1&21',7,21,1*$,5 31R 3828A26005D 3ULQWHGLQ&KLQD