Hayter 407F - Manuals

Hayter 407F – Manual in PDF format online.

Manuals:

Manual

Manual Hayter 407F

Summary

Page 2 - TABLE OF CONTENTS; LIMITED WARRANTY

2 1739579 TABLE OF CONTENTS LIMITED WARRANTY OPERATOR SAFETY ASSEMBLY OPERATION MAINTENANCE TROUBLESHOOTING SPECIFICATIONS REPAIR PARTS 348 1114192123

Page 4 - OPERATOR SAFETY; OWNER’S INFORMATION; Responsibility Of The Owner; The responsibility of the owner is; General Operation

OPERATOR SAFETY 4 1739579 OWNER’S INFORMATION Know your product: If you understand the unit and how the unit operates, you will getthe best performance. As you read this manu-al, compare the illustrations to the unit. Learnthe location and the function of the controls.It is important that you read a...

Page 7 - INTERNATIONAL PICTORIALS; Safety Warning Pictorials

OPERATOR SAFETY 7 1739579 INTERNATIONAL PICTORIALS IMPORTANT: The following pictorials are located on your unit or on literature supplied with the product. Before you operate the unit, learn and understand the purpose for each pictorial. 1 2 6 7 3 8 4 5 Safety Warning Pictorials 1 WARNING 2 IMPORTAN...

Page 8 - ASSEMBLY; CONTENTS OF LITERATURE PACK; TOOLS REQUIRED; REMOVE THE TRIMMER

ASSEMBLY 8 1739581 CONTENTS OF LITERATURE PACK 1 - Operator’s Manual1 - Engine Manual1 - Document of Conformity1 - Warranty Card1 - Safety Glasses1 - Trimmer Line (2 Sets)1 - Bag (4 Screws) WARNING: Always wear safety glasses or eye shields while as- sembling the machine. TOOLS REQUIRED 1 − Knife to...

Page 9 - RAISE THE HANDLE

ASSEMBLY 9 1739579 RAISE THE HANDLE 1. Hold the handle with one hand and loosen both handle adjustment knobs until the ratchet teeth are disengaged. Do not remove the handle adjustment knobs . See Figure 2. 2. Raise the handle to the operating position. 3. Stand in the operator’s position behind the...

Page 10 - ENGINE PREPARATION; Fill Crankcase With Oil; CHECKLIST

ASSEMBLY 10 1739579 ENGINE PREPARATION Note: Engine does not contain OIL orPETROL. WARNING: Follow the engine manufacturer’s instructions for the type of petrol and oil to use. Always use a safety petrol container. Do not smoke when adding petrol to the en- gine. When inside an enclosure, do not fil...

Page 11 - OPERATION; KNOW YOUR POWERTRIM; Trimmer Head Drive Lever −; EYE PROTECTION

OPERATION 11 1739579 KNOW YOUR POWERTRIM READ THE OWNER’S HANDBOOK AND ALL SAFETY RULES BEFORE YOU OPERATE themachine. To familiarise yourself with the location of the controls, compare the illustrations with yourmachine. Save this handbook for future reference. Trimmer Head Recoil Starter Handle Th...

Page 12 - USE THE TRIMMER HEAD

OPERATION 12 1739579 USE THE TRIMMER HEAD DRIVE LEVER 1. To engage the trimmer head, hold the con- trol bail against the handle . Move the trimmer head drive lever forward to en- gage the trimmer head. See Figure 6. Thefaster the engine runs, the faster the trim-mer head will rotate. 2. Once the tri...

Page 13 - START THE ENGINE

OPERATION 13 1739579 START THE ENGINE NOTE: DO NOT BE ALARMED, your engine will smoke the first time it is started. It is burning off the protective coating that is on the internal engine parts. WARNING: Never leave the ma- chine unattended while the en- gine is running. Wait for the trim- mer lines...

Page 14 - MAINTENANCE; SERVICE RECORDS

MAINTENANCE 14 1739579 SERVICE RECORDS Fill in dates as you complete regular service. Before Each Use Every 5 Hours Every 25 Hours Every 100 Hours As Noted SERVICE DATES Check Engine Oil Level √ Check Trimmer Lines √ 1 Check Trimmer Head Engagement √ Engine/Machine Cleaning √ 2 Check Nuts and Bolts ...

Page 15 - LUBRICATION

MAINTENANCE 15 1739579 LUBRICATION Lubricate the Jackshaft Assembly A grease fitting is provided to lubricate the jackshaft assembly. Use a grease gun with au-tomotive type grease to lubricate the jackshaftassembly as shown in Figure 10. Figure 10 Grease Fitting Change Engine Oil Change the engine o...

Page 16 - SPARK PLUG

MAINTENANCE 16 1739579 SPARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted or burned or if the porcelain is cracked. 1. Make sure the spark plug is clean. Clean the spark plug by carefully scraping the electrodes (do not sand blast or use a wirebrush...

Page 17 - SERVICE AND ADJUSTMENT

MAINTENANCE 17 1739579 SERVICE AND ADJUSTMENT WARNING: Before you inspect, clean or service the machine, stop the engine. Make sure that all moving parts have stopped. Disconnect the wire from the spark plug. PROPER CARE OF TRIMMER LINE For the best performance, use a heavygauge 3.9mm (0.155” diamet...

Page 18 - REPLACE THE DRIVE BELT; Trimmer; Engine

MAINTENANCE 18 1739579 REPLACE THE DRIVE BELT To replace the drive belt, see an author-ized service center. STORAGE WARNING: Do not remove petrol while inside a building, near a fire, or while you smoke. Petrol fumes can cause an explosion or a fire. When the machine is put in storage for thirtydays...

Page 19 - TROUBLESHOOTING CHART; TROUBLE

TROUBLESHOOTING CHART 19 1739579 TROUBLE CAUSE CORRECTION Engine does not start. Spark plug wire disconnected. Connect spark plug wire. Engine not primed. Prime engine. Defective or incorrectly gapped spark plug. Inspect or replace spark plug. Fuel tank empty. Add fuel. Dirty carburetor or fuel line...

Page 21 - SPECIFICATIONS; Engine Power Rating Information

21 1739579 Trimmer Line Diameter 3,9 mm (0,155”) Trimmer Line Length 520 mm (21,5”) Height of Cut (Fixed) 76 mm (3”) Dimensions 1400 x 555 x 1000 Engine Briggs 122T02-0188-B1 KW 2,56 Displacement 190 cc (11,57 cu in.) Petrol Capacity 0,95 L (1,0 quarts) Oil Capacity 0,54 - 0,59 L (18-20 oz) Spark Pl...

Page 22 - Order Replacement Parts

1739579 22 Order Replacement Parts Replacement parts, except for the engine, transmission, transaxle or differential,are available from your local Hayter authorised dealer, the store where the mower was purchased or a service shop recommended by the store. If you are unable to obtain parts or servic...

Page 23 - Repair Parts

Page 28 - Torque Specification Chart; Hardware Identification & Torque Specifications

Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7....