Hayter 36 - Manuals

1.5 WARRANTY LIMITED WARRANTY Hayter Limited warrants to the original user/purchaser that this unit shall be free fromdefects in material or workmanship under normal use for a period of two years from thedate of purchase. To qualify for the full benefit of the warranty, the warranty registrationcard...

1.6 SAFETY PRECAUTIONS This safety alert symbol indicates important safety messages. Whenyou see this symbol be alert to the possibility of injury. Carefully readthe following and inform others. Your mower is perfectly safe if used correctly. Failure to observe thefollowing precautions may result in...

1.7 PRECAUTIONS SAFETY Always ensure that the mower is in a safe operating condition.Frequently check all nuts, bolts and screws for tightness. Use only gen-uine Hayter parts. A damaged cutterblade and loose fixing bolt are major hazards. Beforeuse, visually inspect the cutting mechanism to ensure t...

1.9 SAFETY PRECAUTIONS Safety Symbols Safety Alert - Be aware to thepossibility of injury. Danger of severing toes or fin-gers in cutting mechanism. Carefully read the OwnersHandbook before using themachine. Danger of being hit by thrownobjects. Switch off and remove plugfrom mains before performing...

1.10 ASSEMBLING THE MOWER Remove the mower from the packaging and check that the following items have been supplied correctly. If any items are missing contact,your local Hayter dealer. 1. Instruction Sheet 2. Grassbag Frame 3. Grassbag Top Cover4. Grassbag Fabric 5. Supply Cable To prevent accident...

1.11 Forward Travel Position the mower on the grass area to be cut. Carefully uncoil thesupply cable clear of the mower. Ensure that the mains socket isswitched 'OFF' before connecting. Switch 'ON'. Note: We recomend the use of a RCCB unit- Refer to "SafetyPrecautions" - Preparation. Locate ...

Stopping Release the bail arm to stop the motor. WARNING: AVOID ACCIDENTS - The cutterblade may contin-ue to rotate after the mower is switched off Move the height of cut lever sideways to disengage it from the lockingnotch, then push forwards to lower or pull backwards to raise the heightof cut. Re...

1.13 To empty the grassbag raise the rear deflector and pass the grassbagunder the handlebar and lower the rear deflector to rest against the rearof the mower. Pour out the grass clippings and shake the grassbag vigorously to cleanthe airways. Good grass collection depends on good air flow throughth...

1.14 WARNING: PREVENT ACCIDENTS - Take extreme care do not mow across the supply cable. If this should occur, switch off immedi-ately and disconnect the plug from the power supply. Carefully exam-ine the cable for cuts and damage. A defective cable must be replacedbefore the mower is used again. Alw...

1.16 There is very little work to do this month apart from brushing awayleaves. Keep off the grass if frozen or waterlogged. Rake the grass thoroughly. Spike the lawn to aerate and stimulate soilorganisms and root growth and apply lawn sand if necessary. The yearly lawn work programme really starts ...

1.19 Remove grass debris from the top and underside of the deck housingimmediately after use. Regularly check that all securing nuts and bolts are tight. Replacemissing or damaged items immediately. Bolt - Cutterblade fixing Torque 20Nm Plastic Screws - Bottom of Handlebar Torque 3.5Nm General Screw...

1.20 1 2 Turn the mower on its side. Firmly grip the end of the cutterblade (2) with a gloved hand andremove bolt (1). When replacing ensure that the new cutterblade is thecorrect way up with the turned edges facing towards the motor beforelocating onto the two carrier pins. Secure the cutterblade f...

1.22 Handlebar storage: To collapse the handlebar first unscrew the two top securing knobs to allow the top section of the handlebar to pivotforward to rest against the middle section then unscrew the bottom twosecuring knobs sufficiently to allow both top and middle sections to befolded forwards. S...

Test socket by plugging in anoth-er appliance. Remove mower plug and checkRCCB action. Check the supplycable for any obvious signs ofdamage and replace immediatelyif defective. If no obvious faultsare found a serious fault is indi-cated. Contact your HayterDealer. Re-engage plug. Fit a new 13 amp fu...

1 Motor HY100001 1 2 Capacitor HY100002 1 3 Underdeck HY100003 1 4 Throw Plate HY100004 1 5 Wheel - Wide Assy HY100506 2 6 Bearing - Wheel HY100033 12 7 Hub - Cap HY100036 4 8 Starlock 12mm HY100047 4 9 Rod - Rear Axle HY100068 1 10 Wheel - Thin Assy HY100505 4 11 Lever - HOC HY100038 1 12 Spring - ...

1.29 NOTES Notes:- 111-1074(A) 1/11/06 11:33 Page 1.29

Serial No: Motor Type:- 230V Date of Sale:- Your Local Dealer:- CUSTOMER INFORMATION 111-1074(A) 1/11/06 11:33 Page 1.32