Grizzly Industrial T26416 - Manuals

Page 3 - table of contents

table of contents section 1: safety .......................................................................................................2 safety instructions for pneumatic tools .....................................................................3 section 2: introduction ...........................

Page 4 - safety instructions for pneumatic tools; For Your Own Safety Read Instruction Manual; NOTICE

Model T26416 Crown Stapler -2 - section 1: safety safety instructions for pneumatic tools Keep all safety devices in place and in working order. remove adJusting Keys and Wrenches. Form habit of checking to see that keys and adjusting wrenches are removed from tool before operation. Keep WorK area c...

Page 6 - additional safety for staplers

Model T26416 Crown Stapler -4 - additional safety for staplers hand inJuries. do not place your hands near the staple point of entry. a staple can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. safe handling. never point the sta-pler at others! do not keep th...

Page 7 - section 2: introduction; foreword

Model T26416 Crown Stapler -5 - section 2: introduction We are proud to offer this manual! We've made every effort to be exact with the instructions, specifications, drawings, and photographs we used when writing this manual. however, sometimes we still make an occasional mistake. also, owing to our...

Page 8 - unpacking

Model T26416 Crown Stapler -6 - this stapler was carefully packaged for safe transportation. remove the packag-ing materials from around this tool and inspect it. if you discover the tool is dam-aged, please immediately call Customer Service at (570) 546-9663 for advice. save the containers and all ...

Page 10 - compressed air

Model T26416 Crown Stapler -8 - Quick Connector Quick Coupler Air Hose Quick Coupler Quick Connector Lubricator Filter Regulator Air Compressor Your Tool figure 5. installed filter lubricator regulator. compressed air system the Model t26416 is designed to be oper-ated at 70-120 psi using clean, dry...

Page 11 - test run

Model T26416 Crown Stapler -9 - test run prior to using the stapler for regular opera-tions, perform this test run procedure on a scrap workpiece at least 1 1 ⁄ 2 " thick to ensure it functions properly. to test run stapler: 1. insert staples into stapler, following directions in loading staples...

Page 12 - section 4: operations

Model T26416 Crown Stapler -10 - accidental start hazard! disconnect before service or staple replacement. air pressure hazard! never exceed max psi rating for tool. lung / ear inJury hazard! Wear protective equipment when using this tool. section 4: operations eye inJury hazard! Wear safety glasses...

Page 13 - section 5: accessories

Model T26416 Crown Stapler -11 - section 5: accessories g6052—18 gauge 1 ⁄ 4 " crown galv. - 1 ⁄ 2 " g6053—18 gauge 1 ⁄ 4 " crown galv. - 5 ⁄ 8 " g6054 —18 gauge 1 ⁄ 4 " crown galv. - 3 ⁄ 4 " g6055 —18 gauge 1 ⁄ 4 " crown galv. - 7 ⁄ 8 " g6056 —18 gauge 1 ⁄ 4 " cr...

Page 14 - section 6: maintenance; cleaning

Model T26416 Crown Stapler -12 - section 6: maintenance disconnect the stapler from the air supply before cleaning. use a good solvent to clean the nose assembly of the stapler. always be sure that the stapler is dry before using it again. do not allow dust, chips, sand, etc. into the air connectors...

Page 15 - piston assemblies

Model T26416 Crown Stapler -13 - section 7: service always disconnect air from stapler whenever servicing! during mainte-nance, a stapler connected to air may fire accidentally, causing seri-ous personal injury! replacing o-rings & piston assemblies if you use your stapler frequently, replacemen...

Page 16 - troubleshooting; symptom

Model T26416 Crown Stapler -14 - troubleshooting symptom possible cause solution air leaking at trig-ger valve area. 1. o-rings in trigger valve housing are damaged. 1. o-rings must be replaced & operation of safety probe must be checked. air leaking between housing and hose. 1. loose screws in ...

Page 17 - parts

Model T26416 Crown Stapler -15 - parts 101 102 103 104 105 106 107 108 109 110 11 1 113 112 112A 114 115 116 117 118 201 202 203 204 205 206 207 208 209 210 21 1 212 213 301 302 303 304 305 401 402 403 404 405 406 407 408 409 410 41 1 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 4...

Page 18 - parts list

Model T26416 Crown Stapler -16 - parts list REF PART # DESCRIPTION REF PART # DESCRIPTION 101 PT26416101 DEFLECTOR 305 PT26416305 QUICK-DISCONNECT VALVE 102 PT26416102 CYLINDER CAP 401 PT26416401 CAP SCREW M5-.8 X 20 103 PT26416103 CYLINDER CAP REAR SEAL 402 PT26416402 FLAT WASHER 8MM 104 PT26416104...

Page 19 - Warranty

Model T26416 Crown Stapler -17 - Warranty Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or altera...