Grizzly Industrial T20568 - Manuals

Page 2 - safety; NOTICE

safety instructions for pneumatic tools 1. Keep all safety devices in place and in working order. 2. remove adJusting Keys and Wrenches. Form habit of check-ing to see that keys and adjusting wrenches are removed from tool before operation. 3. Keep WorK area clean. Cluttered areas and benches invite...

Page 3 - safety instructions for pneumatic tools

t20568 1 1 ⁄ 4 " brad nailer -1 - 10. use proper air hose for the tool. make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. Wear proper apparel. do not wear loose clothing, gloves, neck-ties, rings, bracelets, or other jew-elry which may get...

Page 4 - additional safety instructions for nailers

t20568 1 1 ⁄ 4 " brad nailer -2 - 1. hand inJuries: do not place your hands near the nail point of entry. a nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. combustible gases: never connect the nailer to pressur-ized oxygen or other combustible ...

Page 6 - introduction; manual accuracy

t20568 1 1 ⁄ 4 " brad nailer -4 - introduction if you have any comments regarding this manual, please write to us at the following address: grizzly industrial, inc. C/o technical documentation manager p.o. box 2069 bellingham, Wa 98227-2069 email: [email protected] most importantly, we stand b...

Page 7 - set up; unpacking; inventory

t20568 1 1 ⁄ 4 " brad nailer -5 - set up unpacking your model t20568 left our warehouse in a carefully packed box. if you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing ...

Page 10 - operations; loading

t20568 1 1 ⁄ 4 " brad nailer -8 - operations loading When replacing nails in your model t20568, follow these guidelines: gauge: 18length: 3 / 8 " – 1 1 ⁄ 4 " Capacity: 100 to load your nailer: 1. diSConneCt nailer From the air Supply! 2. grip the nailer firmly, release the catch lever an...

Page 11 - adjusting depth

t20568 1 1 ⁄ 4 " brad nailer -9 - 5. pull the trigger. — if the nail drove into the wood far enough, continue with your intended operations. — if the nail either went too far or not far enough, then go to the adjusting depth section on this page. 3. depress the safety nose mechanism against your...

Page 14 - cleaning & lubrication; lubricating; cleaning

t20568 1 1 ⁄ 4 " brad nailer -12 - cleaning & lubrication lubricating pneumatic tool oil has been included with your new grizzly nailer to help maintain its useful life. place two to six drops of oil in the nailer air inlet (as shown in figure 8) before every use, or after 2 hours of continu...

Page 15 - troubleshooting; symptom possible cause

t20568 1 1 ⁄ 4 " brad nailer -13 - troubleshooting symptom possible cause solution air leaking at trigger valve area. 1. o-rings in trigger valve hous- ing are damaged. 1. o-rings must be replaced & operation of safety nose must be checked. air leaking between hous-ing and hose. 1. loose scr...

Page 18 - Warranty and returns

grizzly industrial, inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. this warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. this is griz...

Page 19 - Warranty card

Warranty card name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ zip _________phone # ____________________ email ________________________ invoice # ...

Page 20 - place

fold along dotted line grizzly industrial, inc.p.o. box 2069bellingham, Wa 98227-2069 tape along edges--please do not staple name________________________________ street________________________________ city______________state______zip_______ send a grizzly catalog to a friend: place stamp here