Grizzly Industrial T10010 - Manuals

Model T10010 Wet Grinder -8 - CIRCUIT REQUIREMENTS Figure 1. Plug & receptacle type. Amperage Draw The Model T10010 motor draws the follow- ing amps under maximum load: Motor Draw.......................................3 Amps Minimum Circuit Requirement We recommend connecting your machine to a d...

Model T10010 Wet Grinder -9 - Figure 2. Model T10010 inventory. A SECTION 3: SETUP B C The Model T10010 was carefully packed when it left our warehouse. If you discover any parts are damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Sa...

Model T10010 Wet Grinder -10 - Site Considerations Bench Load Refer to the Specifications on Page 6 for the weight and size specifications of your machine. Some workbenches may require additional reinforcement to sup- port both the machine and the workpiece. Placement Location See Figure 3 for the m...

Model T10010 Wet Grinder -11 - Test Run Once your Model T10010 is positioned, test run the machine to make sure it runs properly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immedi- ately, then review the Troubleshooting on Pa...

Model T10010 Wet Grinder -12 - OPERATIONS Grinding Tips The grinder is a safe tool when used prop- erly. In addition to the safety instructions in this manual, the most important safety consideration is to use common sense at all times. What may be okay in one situa- tion, may not be safe in another...

Model T10010 Wet Grinder -14 - To fill and position the reservoir: 1. Make sure the grinder is disconnected from power and that the grinding wheel is not rotating. 2. Remove reservoir and fill with water to just below the V-shaped notch. 3. Attach the reservoir to the grinder. — If the grinder is go...

Model T10010 Wet Grinder -15 - Here are some tips for using your wet grinder water reservoir: • Check the water level before every use and be sure the wheel is wet before you begin grinding. DO NOT use the grinder without water. • Leaving the grinding wheel stored in water will cause damage to the w...

Model T10010 Wet Grinder -16 - Wheel Dressing Depending on the type of grinding you do, the grinding wheel may require periodic dressing. A variety of dressing tools are available (see Accessories , Page 17 ) and can be used to restore the abrasive quality of the wheel surface and bring the wheel ed...

Model T10010 Wet Grinder -17 - SECTION 5: ACCESSORIES T10024—Accessory Kit #2 Includes a stone dresser and fixtures for sharpening scrapers, screwdrivers and hollow chisels. Figure 15. Model T10024. T10023—Accessory Kit #1 Includes fixtures for sharpening small knives, large knives, scis- sors and axe...

Model T10010 Wet Grinder -19 - SECTION 6: MAINTENANCE ! Always DISCONNECT POWER before servicing, adjusting, or doing main-tenance to reduce the risk of acci-dental injury or electrocution. For optimum performance from your machine, routinely check the condition of the following items and repair or ...

Model T10010 Wet Grinder -20 - SECTION 7: SERVICE Symptom Possible Cause Solution Motor will not start; fuses or circuit breakers blow 1. Disabling key is at fault. 2. Open circuit in motor or loose connections. 3. Start capacitor is at fault. 4. Short circuit in motor or loose connections. 5. Incor...

Model T10010 Wet Grinder -22 - ����� ������ �� �� �� ����� ��������� ����� ������ �� �� ������������� �������������������� �� �� �� ����� ������� ����� ��� ����������� ��� ��� ��������� REDBLUEBROWN �� �� �� ��������������������������� ���������������� Wiring Diagram Figure 20. Switch connections. F...

Model T10010 Wet Grinder -23 - Main Breakdown & Parts List �� �� �� � � � � � � � � � � � � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ���� ���� REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT10010001 ANGLE GUIDE 21 PT10010021 GRINDER CASE 2 PT10...

Model T10010 Wet Grinder -24 - 101 102 103 104 Warning Labels Breakdown & Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 101 PT10010101 ROTATION DIRECTION ARROW 103 PT10010103 RESPIRATOR LABEL VERT 102 PT10010102 MACHINE ID LABEL 104 PLABEL-12A READ MANUAL-VERTICAL NS 7/05

WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte- nance. This is Gr...