Grizzly Industrial H8231 - Manuals

Page 2 - Safety Instructions For Pneumatic Tools; For Your Own Safety Read Instruction Manual; SAFETY; NOTICE

Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN . Cluttered areas and benches inv...

Page 4 - Additional Safety Instructions for Nailers

H8230/H8231 15° Roofing Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, punctur-ing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible ga...

Page 5 - INTRODUCTION; Foreword

H8230/H8231 15° Roofing Nailer -3 - INTRODUCTION The specifications, details, and pho-tographs in this manual represent the Model H8230/H8231 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improve-ment, changes may be made at any time with no obligation on...

Page 6 - SET UP; Inventory; Unpacking

H8230/H8231 15° Roofing Nailer -4 - SET UP Inventory Your nailer was carefully packaged for safe shipping. If you discover any damage after you have signed for delivery, immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing materi-als for possible inspec...

Page 7 - Compressed Air

H8230/H8231 15° Roofing Nailer -5 - The Model H8230/H8231 is designed to operate at 70-110 PSI using clean, dry, regulated, compressed air. DO NOT exceed the 120 PSI maximum operating pressure for your model. An in-line filter/lubricator/regulator unit, depicted in Figure 2 , can be installed and sh...

Page 8 - Safety Check

H8230/H8231 15° Roofing Nailer -6 - A safety mechanism on the nose of the nailer protects against accidental firing. The nailer is designed to only fire when the safety nose is depressed and the trig-ger is pulled. The nailer should not fire otherwise. This nailer also features a trigger lock switch...

Page 9 - OPERATIONS; Loading

H8230/H8231 15° Roofing Nailer -7 - OPERATIONS Loading When replacing nails in your Model H8230/H8231, follow these guidelines: Nail Type: Flat Wire Welded Coil 15° Rooﬁng Nail Length: H8230 3 ⁄ 4 "–1 3 ⁄ 4 " H8231 1 3 ⁄ 4 "–2 3 ⁄ 4 " Capacity: H8230 120 Nails H8231 225–300 Nails To ...

Page 10 - Firing Nails

H8230/H8231 15° Roofing Nailer -8 - If you have not read the safety instruc-tions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer con-nects to the air supply, unless your air system...

Page 12 - Rings

H8230/H8231 15° Roofing Nailer -10 - Replacing Pistons /O- Rings If you use your nailer on a daily basis, replacement pistons are cheap insurance against wasted down time and lost profits in the event that a piston or piston shaft wears out. 6. Open the nose cover as if to clear a jammed nail. 7. Wa...

Page 13 - ACCESSORIES

H8230/H8231 15° Roofing Nailer -11 - ACCESSORIES G2820 —Pneumatic Tool Oil 8 oz.G2821—Pneumatic Tool Oil 1 Pint Use the right oil! This pneumatic tool oil offers outstanding heat displacement and friction reduction without eating away at delicate air components like detergent motor oils. Stock up wi...

Page 14 - CLEANING & LUBRICATION; Cleaning

H8230/H8231 15° Roofing Nailer -12 - CLEANING & LUBRICATION Cleaning Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may res...

Page 15 - TROUBLESHOOTING; Symptom

H8230/H8231 15° Roofing Nailer -13 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trig-ger valve area. 1. O-rings in trigger valve hous- ing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between housing and hose. 1. Loose screw...

Page 20 - WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte-nance. This is Gri...