Grizzly Industrial H7678 - Manuals

Page 2 - SAFETY; NOTICE

Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN . Cluttered areas and benches inv...

Page 3 - Safety Instructions For Pneumatic Tools

H7678 18 Gauge Deep Stapler Kit -1 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck-ties, rings, bracelets, or other jew-elry which may get ...

Page 4 - Additional Safety Instructions for Staplers

H7678 18 Gauge Deep Stapler Kit -2 - 1. HAND INJURIES. Do not place your hands near the staple point of entry. A staple can deflect and tear through the surface of the workpiece, punc-turing your hand or fingers. 2. COMBUSTIBLE GASES. Never connect the stapler to pressurized oxygen or other combusti...

Page 6 - INTRODUCTION; Foreword; Tool Data

H7678 18 Gauge Deep Stapler Kit -4 - INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have...

Page 7 - SET UP; Unpacking; Inventory

H7678 18 Gauge Deep Stapler Kit -5 - SET UP Figure 1. Model H7678 inventory. Unpacking Your Model H7678 left our warehouse in a carefully packed box. If you discover the stapler is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save...

Page 9 - Safety Yoke

H7678 18 Gauge Deep Stapler Kit -7 - Safety Yoke A safety yoke mechanism on the nose of the stapler acts as a safety device. When the trigger is pressed, the stapler will not fire until the safety yoke mechanism is depressed. Before you use your stapler for the first time, check the safety yoke mech...

Page 10 - OPERATIONS; Loading; Operating

H7678 18 Gauge Deep Stapler Kit -8 - OPERATIONS Loading When replacing staples in your Model H7678, follow these guidelines: Gauge: 18Length: 3 ⁄ 8" –1 1 ⁄ 2 " Capacity: 100Crown: 1 ⁄ 4 " To load your stapler: 1. DISCONNECT STAPLER FROM THE AIR SUPPLY! 2. Grip the stapler firmly, unlock ...

Page 12 - Clearing Jammed

H7678 18 Gauge Deep Stapler Kit -10 - A jammed staple must be cleared before using the stapler again. To clear a jammed staple from the dis-charge area: 1. DISCONNECT STAPLER FROM THE AIR SUPPLY! 2. Unlock the catch lever and slide the magazine pusher all the way back. 3. Remove the staple stick fro...

Page 13 - Rings

H7678 18 Gauge Deep Stapler Kit -11 - Replacing Pistons /O- Rings If you use your stapler day in and day out, repair pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. A replacement piston and O-ring kit, part PH7678075...

Page 14 - CLEANING & LUBRICATION; Cleaning

H7678 18 Gauge Deep Stapler Kit -12 - CLEANING & LUBRICATION Cleaning Disconnect the stapler from the air supply before cleaning. Use a good solvent to clean the nose assembly of the stapler. Always be sure that the stapler is dry before using it again. Do not allow dust, chips, sand, etc. into ...

Page 17 - TROUBLESHOOTING; Symptom

H7678 18 Gauge Deep Stapler Kit -15 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trig-ger valve area. 1. O-rings in trigger valve hous- ing are damaged. 1. O-rings must be replaced & operation of safety yoke must be checked. Air leaking between housing and hose. 1. Loose scre...

Page 18 - WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz...

Page 19 - WARRANTY CARD

WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...

Page 20 - Place

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here