Grizzly Industrial H7677 - Manuals

H7677 18 Gauge Stapler Kit -6 - SECTION 2: INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If yo...

H7677 18 Gauge Stapler Kit -7 - SECTION 3: SET UP Figure 1. Model H7677 inventory. Unpacking Your Model H7677 stapler kit left our ware-house in a carefully packed box. If you discover the stapler is damaged after you have signed for delivery, please immedi- ately call Customer Service at (570) 546-...

H7677 18 Gauge Stapler Kit -9 - Safety Yoke A safety yoke mechanism (bump fire) on the nose of the stapler acts as a safety device. When the trigger is pulled, the stapler will not fire until the safety yoke mechanism is depressed. Before you use your stapler for the first time, check the safety yok...

H7677 18 Gauge Stapler Kit -10 - SECTION 4: OPERATIONS Loading Figure 3. Latching pusher in groove. When replacing staples in your Model H7677, follow these guidelines: Gauge: 18Length: 1 ⁄ 2" –1" Capacity: 100Crown: 1 ⁄ 4" To load your stapler: 1. DISCONNECT STAPLER FROM THE AIR SUPPLY!...

H7677 18 Gauge Stapler Kit -11 - 5. Pull the trigger. — If the staple drove into the wood far enough, continue with your intended operations. — If the staple either went too far or not far enough, then adjust the air pressure. More air pressure will make the staple go deeper and less air pressure wi...

H7677 18 Gauge Stapler Kit -12 - A jammed staple must be cleared before using the stapler again. The two places where a staple can get jammed are the magazine and the discharge area. To clear a jammed staple from the dis-charge area: 1. DISCONNECT STAPLER FROM THE AIR SUPPLY! 2. Pull back and latch ...

H7677 18 Gauge Stapler Kit -13 - Replacing Pistons /O- Rings If you use your stapler day in and day out, repair pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. A replacement piston and O-ring kit, part PH7677069, may...

H7677 18 Gauge Stapler Kit -14 - SECTION 5: MAINTENANCE Cleaning Use a good solvent to clean the nose assembly of the stapler. Always be sure that the stapler is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the stapler; this may result i...

H7677 18 Gauge Stapler Kit -17 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trig-ger valve area. 1. O-rings in trigger valve hous- ing are damaged. 1. O-rings must be replaced & operation of safety yoke must be checked. Air leaking between housing and hose. 1. Loose screws in...

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz...

WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here