Grizzly Industrial H7665 - Manuals

Page 2 - SAFETY; NOTICE

Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN . Cluttered areas and benches inv...

Page 3 - Safety Instructions For Pneumatic Tools

H7665 21° Round Head Framing Nailer -1 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck-ties, rings, bracelets, or other jew-elry which may ...

Page 4 - Additional Safety Instructions for Nailers

H7665 21° Round Head Framing Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustibl...

Page 6 - INTRODUCTION; Foreword

H7665 21° Round Head Framing Nailer -4 - INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you ...

Page 7 - SET UP; Unpacking; Inventory

H7665 21° Round Head Framing Nailer -5 - SET UP Figure 1. Model H7665 inventory. Unpacking Your Model H7665 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. S...

Page 10 - OPERATIONS; Loading

H7665 21° Round Head Framing Nailer -8 - OPERATIONS Loading Figure 3. Sliding magazine back and engaging the catch. When replacing nails in your Model H7665, follow these guidelines: Type: Round Head Angle: 21° Diameter: 0.113"Length: 2"–3 1 ⁄ 2 " Capacity: 75 To load your nailer: 1. DIS...

Page 11 - Operating

H7665 21° Round Head Framing Nailer -9 - Operating If you have not read the safety instruc-tions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer con-nects to the air supply. To oper...

Page 12 - Clearing Jammed; Adjusting Depth

H7665 21° Round Head Framing Nailer -10 - A jammed nail must be cleared before using the nailer again. To clear a jammed nail from the dis-charge area: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Pull the magazine handle all the way back until it latches. 3. Remove the nail stick from the maga- zin...

Page 13 - Replacing

H7665 21° Round Head Framing Nailer -11 - Replacing Pistons /O-Rings If you use your nailer day in and day out, repair pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. The piston repair kit part number for the Model H...

Page 14 - CLEANING & LUBRICATION; Cleaning

H7665 21° Round Head Framing Nailer -12 - CLEANING & LUBRICATION Cleaning Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this ma...

Page 17 - TROUBLESHOOTING; Symptom

H7665 21° Round Head Framing Nailer -15 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trig-ger valve area. 1. O-rings in trigger valve hous- ing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between housing and hose. 1. Loose ...

Page 18 - WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz...

Page 19 - WARRANTY CARD

WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...

Page 20 - Place

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here