Grizzly Industrial H6329 - Manuals

Page 3 - safety instructions for pneumatic tools; safety; NOTICE

-1 - Model h6329 2 1 ⁄ 2 gallon paint tank safety instructions for pneumatic tools 1. read this manual. this tool may cause personal injury if used incor-rectly. this manual contains proper safety and operating instructions that must be followed to reduce this risk. 2. Wear eye protection. this tool...

Page 5 - additional safety instructions for paint tanks

-3 - Model h6329 2 1 ⁄ 2 gallon paint tank no list of safety guidelines is complete, because every work environment is different. always consider safety first and use common sense. failure to use this tool with caution and respect could result in serious personal injury. 1. read this manual. this ma...

Page 6 - introduction; specifications

Model h6329 2 1 ⁄ 2 gallon paint tank -4 - introduction specifications foreword the spec ific ations, details, and photographs in this manual represent the Model h6329 as supplied when the manual was prepared. however, owing to grizzly’s policy of continuous improvement, changes may be made at any t...

Page 7 - inventory; setup; unpacking

-5 - Model h6329 2 1 ⁄ 2 gallon paint tank h6329 inventory (figure 1) ............... Qtya. paint tank............................................ 1 b. Caster Wheel Assemblies ................... 4—hex nuts M8-1.25 ................................ 4—Flat Washers 8MM ............................... 4...

Page 8 - tank assembly

Model h6329 2 1 ⁄ 2 gallon paint tank -6 - tank assembly to assemble the paint tank: 1. open the lid and remove the hardware shipped with the tank. 2. install the four caster assemblies with the hex nuts and washers, as shown in figure 3. 5. Connect the 1 / 4 " push-on hose fittings to your air ...

Page 9 - operations; tank regulator and

-7 - Model h6329 2 1 ⁄ 2 gallon paint tank operations the pressure regulator on the paint tank controls the pressure in the tank. in turn, the paint is fed to the spray gun at this tank pressure. note: The pressures suggested for the gun types listed below are typical operating guidelines: internal ...

Page 10 - operation

Model h6329 2 1 ⁄ 2 gallon paint tank -8 - read the manual before operation. become familiar with this tool, its safety instructions, and its operation before beginning any work. serious personal injury may result if safety or operational information is not understood or followed. to use the paint t...

Page 11 - cleaning and lubrication; cleaning the tank

-9 - Model h6329 2 1 ⁄ 2 gallon paint tank cleaning and lubrication 3. open the tank lid. 4. empty and clean the tank of all paint, and fill it with 1 quart of solvent. 5. replace the lid, tighten the clamps, and spray the gun until it sprays clean solvent. note: Check with local laws regarding this...

Page 12 - tank troubleshooting

Model h6329 2 1 ⁄ 2 gallon paint tank -10 - tank troubleshooting symptom possible cause solution Air escaping from regulator port. 1. Broken or damaged dia- phragm in tank regulator. 1. replace tank regulator. pressure dropping slowly on regulator. 1. dirty or worn valve seat in regulator. 2. loose ...

Page 13 - troubleshooting

-11 - Model h6329 2 1 ⁄ 2 gallon paint tank troubleshooting symptom possible cause solution Fluttering or spitting spray. 1. dry or worn fluid tip seat per- mits air to seep into fluid pas-sage. 2. Material level too low. 3. Fluid tip or filter obstructed. 4. dry needle packing. 1. tighten fluid tip...