Grizzly Industrial H6231Z 10-TON - Manuals

-4- model h6231z (mfg. since 1/10) 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing loss. 5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry that can catch in moving parts. Wear protective hair covering to con...

model h6231z (mfg. since 1/10) -5- ­­ 7. Only allOw trained and prOp- erly supervised persOnnel tO Operate machinery. ­ Make­ sure­­ operation­ instructions­ are­ safe­ and­ clearly­ understood. 8. Keep children/visitOrs away. Keep­ all­ children­ and­ visitors­ away­ from­ machinery.­ When­ machine...

-6- model h6231z (mfg. since 1/10) additional Safety for Hydraulic Presses 1. avOiDiNg OvERLOaD. Exceeding rated press capacity can damage the press, shatter a workpiece, or launch a press pin causing a severe impact injury. When the press has reached its maximum pressure or the pump lever becomes s...

-8- model h6231z (mfg. since 1/10) Wear safety glasses dur- ing the entire setup pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire man- ual to become familiar with the controls and operations before using the machine! SECTiON 2: SETuP the following ...

model h6231z (mfg. since 1/10) -9- inventory the following is a description of the main compo-nents shipped with your machine. lay the compo-nents out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefu...

-10- model h6231z (mfg. since 1/10) Site Considerations figure 4. minimum working clearances. Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be ...

model h6231z (mfg. since 1/10) -11- assembly To assemble your press: 1. put on safety glasses and heavy leather boots. 2. place both U-beams parallel on the floor so the flanges are facing one another and both beams have their row of pin holes at the same end, as shown in figure 7 . 3. orient the be...

-14- model h6231z (mfg. since 1/10) 19. With the help of another person, position the press on the workbench where you want to mount it. 20. Based on your choice of fasteners discussed under Mounting , use the pre drilled holes in the base rails as a guide to drill and mount your press to the workbe...

model h6231z (mfg. since 1/10) -15- SECTiON 3: OPERaTiONS To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations. Operation Overview this overview is not intended to be an exact step-by-step procedure, but rather a general...

model h6231z (mfg. since 1/10) -17- figure 22. Arbor press stand (press not included). SECTiON 4: aCCESSORiES ACCEssoriEs g8983—Tilting Roller Stand Adjusts from 26" to 44", 0º-45º. 150 lb. capacity. g8984—Single Roller Stand Adjusts from 26 5 ⁄ 8 " to 45". 250 lb. capacity. g8985—5 ...

-18- model h6231z (mfg. since 1/10) SECTiON 5: MaiNTENaNCE always relieve hydraulic pressure before performing maintenance. failure to do this may result in serious personal injury. Cleaning the model h6231z is relatively easy. Vacuum excess metal chips or contaminants away from hydraulic seals and ...

model h6231z (mfg. since 1/10) -19- SECTiON 6: SERviCE piston is weak or does not reach rated pressing capacity. 1. pump reservoir is low on oil.2. system has air bubbles trapped in pump.3. Control valve is at fault. 4. pump or piston is at fault. 1. Fill pump reservoir to correct oil level Page 18 ...

model h6231z (mfg. since 1/10) -21- Main Breakdown SECTiON 7: PaRTS 12 25 24 1 2 16 3 4 15 5 6 9 21 20 18 14 22 34 35 36 8 37 32 33 13 11 10 30 17 27 28 29 19 25 26 27 7 31 REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6231Z001 PUMP LEVER W/GRIP 19 PH6231Z019 U-BEAM W/O PUMP BRACKET 2 PH6231Z002...

-22- model h6231z (mfg. since 1/10) Label Placement Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MuST maintain the original location and readability of the labels on the machine. if any label is removed or becomes unreadable, REPLaCE that label befor...

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

WaRRaNTy aND RETuRNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main...

Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ ORDER 24 HOURS A DAY! 1-800-523-4777 Visit Our Website Today For Current Specials!