Grizzly Industrial H6146 - Manuals

Page 2 - SAFETY; Safety Instructions for Machinery; NOTICE

For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages...

Page 4 - Additional Safety Instructions for Nailers

H6146 34° Clipped Head Framing Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combusti...

Page 6 - INTRODUCTION; Foreword

H6146 34° Clipped Head Framing Nailer -4 - INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have a...

Page 7 - SET UP; Unpacking; Inventory

H6146 34° Clipped Head Framing Nailer -5 - SET UP Figure 1. Model H6146 inventory. Unpacking Your Model H6146 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice....

Page 9 - Safety Yoke

H6146 34° Clipped Head Framing Nailer -7 - Safety Yoke A safety yoke mechanism (bump fire) on the nose of the nailer acts as a second-ary safety device. When the trigger is pressed, the nailer will not fire until the safety yoke mechanism is depressed. Before you use your nailer for the first time, ...

Page 10 - OPERATIONS; Loading; Operating

H6146 34° Clipped Head Framing Nailer -8 - OPERATIONS Loading Figure 3. Sliding pusher toward the catch lever. When replacing nails in your Model H6146, follow these guidelines: Diameter: 7 ⁄ 64 "- 1 ⁄ 8 " Length: 2"-3 1 ⁄ 2 " Capacity: 100Strip Angle: 34° To load your nailer: 1. DIS...

Page 11 - Adjusting Depth

H6146 34° Clipped Head Framing Nailer -9 - Figure 6. Loosening cap screw for depth adjustment. The nose of the gun houses a depth adjust-ment mechanism for setting the nail depth. To adjust the depth: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. If the nail is driven too far into the workpiece, loos...

Page 12 - Clearing Jammed

H6146 34° Clipped Head Framing Nailer -10 - A jammed nail must be cleared before using the nailer again. The two places where a nail can get jammed are the maga-zine and the discharge area. To clear a jammed nail from the maga-zine: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2 . Pull back and lock th...

Page 13 - Rings

H6146 34° Clipped Head Framing Nailer -11 - Replacing Pistons /O- Rings If you use your nailer day in and day out, repair pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. 5. The top of the piston should now be visible...

Page 14 - CLEANING & LUBRICATION; Cleaning

H6146 34° Clipped Head Framing Nailer -12 - CLEANING & LUBRICATION Cleaning Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this ...

Page 17 - TROUBLESHOOTING; PROBLEM

H6146 34° Clipped Head Framing Nailer -15 - TROUBLESHOOTING 1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws.2. Replace O-ring.3. Tighten air fitting & use teflon tape. 1. Replace damaged seals. 1. Tighten screws and fit- tings. 2. Clean nose.3. Clean...

Page 18 - WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz...

Page 19 - WARRANTY CARD

Name _________________________________________________________________________Street ________________________________________________________________________City____________________State________Zip_________Phone Number____________E-Mail___________________FAX ____________Model # H6146 34° Clipped Hea...

Page 20 - Send a Grizzly Catalog to a friend:; Place

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here