Grizzly Industrial H6141 - Manuals

Page 2 - SAFETY; NOTICE

H6141 Air Palm Nailer -2 - Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. DO NOT USE IN DANGEROUS ENV...

Page 3 - Safety Instructions For Pneumatic Tools

H6141 Air Palm Nailer -3 - 8. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. 9. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretch-ing. 10. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings,...

Page 4 - Additional Safety Instructions for Nailers

H6141 Air Palm Nailer -4 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a p...

Page 5 - INTRODUCTION; Foreword

H6141 Air Palm Nailer -5 - INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have any servi...

Page 6 - SET UP; Unpacking; Inventory

H6141 Air Palm Nailer -6 - SET UP Figure 1. Model H6141 inventory. Unpacking Your Model H6141 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the contai...

Page 8 - OPERATIONS; General Operations

H6141 Air Palm Nailer -8 - OPERATIONS General Operations If you have not read the safety instruc-tions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer con-nects to the air supply. T...

Page 9 - Rings

H6141 Air Palm Nailer -9 - Replacing Pistons /O- Rings If you use your nailer day in and day out, replacement pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. 6. Push the ram pin towards the inside of the nailer. This...

Page 10 - CLEANING & LUBRICATION; Cleaning

H6141 Air Palm Nailer -10 - CLEANING & LUBRICATION Cleaning Use a good solvent to clean the nose piece and depth guide of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may...

Page 12 - TROUBLESHOOTING

H6141 Air Palm Nailer -12 - TROUBLESHOOTING Symptom Possible Cause Possible Solution Air leaking between housing and hose. 1. Loose screws in housing.2. Damaged O-ring.3. Loose air fitting. 1. Tighten screws.2. Replace O-ring.3. Tighten air fitting and use teflon tape. Air leaking between housing an...

Page 14 - WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz...

Page 15 - WARRANTY CARD

WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...

Page 16 - Place

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here