Grizzly Industrial G9922 - Manuals

Grizzly Industrial G9922 – Manual in PDF format online.

Manuals:

Manual

Manual Grizzly Industrial G9922

Summary

Page 3 - Table of Contents

Table of Contents INTRODuCTION ............................................................................................................................... 4 Foreword .....................................................................................................................................

Page 4 - INTRODuCTION; foreword

-4- g9922 (mfg. since 12/01) INTRODuCTION foreword We are proud to offer the Model g9922 oscillating spindle sander. this machine is part of a grow- ing grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free,...

Page 5 - Identification

g9922 (mfg. since 12/01) -5- figure 1. identification. A. sanding table b. sanding drum C. table angle lock Knob D. Machine Base E. Machine stand f. on/oFF switch G. table Miter slot h. Miter gauge Identification B C d E F g a h

Page 6 - MODEL G9922 OSCILLATING SPINDLE SANDER

-6- g9922 (mfg. since 12/01) The information contained herein is deemed accurate as of 6/15/2008 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G9922 MACHINE DAT...

Page 8 - NOTICE; Safety Instructions for Machinery

-8- g9922 (mfg. since 12/01) 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing loss. 5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry that can catch in moving parts. Wear protective hair covering to contain l...

Page 11 - SECTION 2: CIRCuIT REQuIREMENTS

g9922 (mfg. since 12/01) -11- figure 2. typical 5-15 plug and receptacle. Grounding Prong is Longest of the Three Prongs Current Carrying Prongs Grounded Outlet 110v Operation full Load Amperage Draw this machine draws the following amps under maximum load: amp draw ....................................

Page 12 - Setup Safety; unpacking; Items Needed for

-12- g9922 (mfg. since 12/01) Wear safety glasses dur- ing the entire setup pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Setup Safety SECTION 3: SETuP T...

Page 13 - Inventory

g9922 (mfg. since 12/01) -13- Inventory the following is a description of the main compo- nents shipped with your machine. lay the compo- nents out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully...

Page 14 - hardware Recognition Chart

-14- g9922 (mfg. since 12/01) hardware Recognition Chart

Page 15 - Site Considerations

g9922 (mfg. since 12/01) -15- floor Load refer to the Machine Data Sheet for the weight and footprint specifications of your machine. some residential floors may require additional reinforcement to support both the machine and operator. Placement Location Consider existing and anticipated needs, siz...

Page 16 - Mounting to Shop

-16- g9922 (mfg. since 12/01) although not required, you may choose to mount your new machine to the floor. Because this is an optional step and floor materials may vary, floor mounting hardware is not included. generally, you can either bolt your machine to the floor or mount it on machine mounts. ...

Page 17 - Assembly

g9922 (mfg. since 12/01) -17- Assembly assembly for the Model g9922 consists of put- ting together the machine stand, attaching the machine to the stand, then inserting the sanding spindle. To assemble the machine: 1. lay out two legs, one upper brace and one lower brace, then connect them using fou...

Page 20 - Test Run

-20- g9922 (mfg. since 12/01) 5. turn the machine OFF . 6. remove the switch disabling key, as shown in figure 19 . Test Run once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. the test run consists of verifying the following: 1) the...

Page 21 - SECTION 4: OPERATIONS; Operation Safety

g9922 (mfg. since 12/01) -21- SECTION 4: OPERATIONS Damage to your eyes and lungs could result from using this machine without proper pro- tective gear. Always wear safety glasses and a respirator when operating this machine. NOTICE If you have never used this type of machine or equipment before, WE...

Page 22 - Table Tilt; o Table Stop

-22- g9922 (mfg. since 12/01) Table Tilt the table on the Model g9922 can be tilted up to 45° for sanding beveled edges. To tilt the table: 1. disConnECt sandEr FroM poWEr! 2. loosen the two lock knobs, located on each side of the table tilt assembly ( figure 22 ). figure 22. table lock knobs. 3. ad...

Page 23 - Contour Sanding; Miter Gauge

g9922 (mfg. since 12/01) -23- Contour Sanding To sand a workpiece: 1. disConnECt sandEr FroM poWEr! 2. adjust the table tilt, if desired. 3. Ensure that the spindle hex nut is secured tightly and that the work area is free of obstructions and obstacles. 4. Connect the sander to power, turn ON the sp...

Page 24 - Sanding Sleeve

-24- g9922 (mfg. since 12/01) Sanding Sleeve the sanding sleeves on the Model g9922 can be replaced when they become worn or damaged. To replace sanding sleeves: 1. disConnECt sandEr FroM poWEr! 2. use a 19mm wrench on the sanding drum base nut to keep the spindle from turning ( figure 29 ). 3. remo...

Page 25 - SECTION 5: ACCESSORIES

g9922 (mfg. since 12/01) -25- SECTION 5: ACCESSORIES aCCEssoriEs T20501—face Shield, 4" Crown, ClearT20502—face Shield, 7" Crown, ClearT20448—Economy Clear Safety GlassesT20452—"Kirova" Anti-Reflective GlassesT20456—"Dakura" Clear Safety Glassesh0736—Shop fox ® Safety Glasses...

Page 27 - SECTION 6: MAINTENANCE; Schedule; Lubrication

g9922 (mfg. since 12/01) -27- SECTION 6: MAINTENANCE Always disconnect power to the machine before performing maintenance. failure to do this may result in serious person- al injury. For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions gi...

Page 30 - Wiring Diagram

-30- g9922 (mfg. since 12/01) White Neutral Black Hot Green Ground 110 VAC 5-15 Plug Ground Ground Ground View this page in color at www.grizzly.com. WARNING! SHOCK HAZARD! Disconnect power before working on wiring. MOTOR 110V ON/OFF Switch (Viewed from behind) Start Capacitor 250MFD 125VAC Start Ca...

Page 31 - Parts breakdown

g9922 (mfg. since 12/01) -31- Parts breakdown 56 52 51 50 62 60 61 59 58 57 64 68 39 67 69 53 54 70 51 52 71 72 73 79 48 76 74 41 41 30 51 52 78 10 41 51 52 78 10 85 83 84 43 44 42 30 87 39 40 86 86-1 52 80 82 59 18 81 77 38 34 35 36 37 33 30 31 32 28, 28V2* 20 19 18 17 55, 55V2* 6 5 7 23 22 97 21, ...

Page 32 - Parts List

-32- g9922 (mfg. since 12/01) REF PART # DESCRIPTION REF PART # DESCRIPTION 5 P9922005 FLAT KEY 100 x 356 x 2 55V2 P6005ZZ BALL BEARING 6005ZZ V2.12.01 6 P9922006 CONNECTION PLATE 56 PCAP11M CAP SCREW M8-1.25 X 16 7 P9922007 WORM GEAR SHAFT 57 PS62M PHLP HD SCR M6-1 X 30 8 P9922008 PINION GEAR 58 P9...

Page 33 - WARRANTY CARD

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

Page 35 - WARRANTy AND RETuRNS; WARRANTY AND RETURNS

WARRANTy AND RETuRNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main...

Page 36 - ORDER

Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ ORDER 24 HOURS A DAY! 1-800-523-4777 Visit Our Website Today For Current Specials!