Grizzly Industrial G7945 - Manuals

-4- G7945/46 Radial Drill Press 1. ALWAYS OPERATE YOUR DRILL PRESS AT SPEEDS that are appropriate for the drill bit size and the material that you are drilling. 2. FEED THE DRILL BIT EVENLY INTO THE WORKPIECE. Back the bit out of deep holes and clear the chips with a brush after you have turned the ...

G7945/46 Radial Drill Press -5- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 10-amp fuse or circuit breaker should be usedwhen fusing this drill press. Circuits breakersrated any higher may not be adequate to protectthe circuit from power surges. If you find it necessary to use an extension cord...

-6- G7945/46 Radial Drill Press SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G7945/46Radial Drill Press. The Model G7945/46 is part ofa growing Grizzly family of fine woodworkingmachinery. When used according to the guide-lines set forth in this manual, you can expectyears of trou...

G7945/46 Radial Drill Press -7- If moving this machineup or down stairs, themachine must be dis-mantled and moved insmaller pieces. Makesure floor and stairstructures are capable ofsupporting the com-bined weight of themachine parts and thepeople moving them. The Model G7945/46 is shipped from the m...

G7945/46 Radial Drill Press -9- SECTION 4: ASSEMBLY Beginning Assembly Most of your Model G7945/46 Radial Drill Presshas been assembled at the factory, but someparts must be assembled or installed after deliv-ery. We have organized the assembly processinto steps. Please follow along in the order pre...

-10- G7945/46 Radial Drill Press The Model G7945 comes with a one piece squaretable and support as shown in Figure 4 . The Model G7946 comes with a round table and twopiece hinged table support. 1. Insert the pinion gear into the hole on the sideof the bracket from the inside, starting with theshaft...

G7945/46 Radial Drill Press -11- The headstock repre-sents a heavy load. Seekassistance before begin-ning this step. Figure 8 . Lock Handles and gib location. 1. Make sure the locking gib is in the recessedpocket on the inside edge of the headstockopening. See Figure 8. 2. With the help of an assist...

-12- G7945/46 Radial Drill Press SECTION 5: ADJUSTMENTS Unplug the drill press before changing speeds. The drill press has 5 speeds ranging from 550 to 3470 R.P.M. There is a speed chartlocated under the belt guard. Refer to this chartwhen setting a speed. 1. Loosen the belt tension lock knob on the...

G7945/46 Radial Drill Press -13- Your radial drill press comes with a depth stop foruse when drilling. Follow the instructions belowfor use. 1. Loosen the depth collar lock knob. See Figure 11 . 2. Secure the wood stock you will be drillingonto the drill press table. 3. With the desired bit installe...

-14- G7945/46 Radial Drill Press The Model G7945 table can be adjusted for height and angle. The G7946 adds the adjust-ments of table distance from column and rotation.Follow these instructions to adjust height: 1. Loosen the table support bracket lock han-dle. Turn the table hand crank to lift or l...

G7945/46 Radial Drill Press -15- Head Adjustments Figure 16. Guide pin location. The headstock can be tilted from 45° clockwise to 90° counterclockwise. 1. Loosen the lock handle on the right side ofthe headstock. 2. Pull out the guide pin located on the left sideof the headstock and rotate the pin ...

-16- G7945/46 Radial Drill Press SECTION 6: OPERATIONS Test Run Drill Bit Changes Care must be taken to secure the bit firmly inplace. When changing bits, proceed as follows: 1. Disconnect the machine from the powersource. 2. Open the chuck wide enough to accept anew bit. 3. Install the bit so the c...

G7945/46 Radial Drill Press -17- SECTION 7: MAINTENANCE Lubrication V-Belt Since all bearings are shielded and permanentlylubricated, simply leave them alone until theyneed to be replaced. Do not lubricate them. Inspect regularly for tension and wear. Check pul-leys to ensure that they are properly ...

G7945/46 Radial Drill Press -19- Design Type ....................................................................................................Bench Model Overall Dimensions: Table ................................................................................................................8 5 ⁄...

-20- G7945/46 Radial Drill Press Design Type ......................................................................................................Floor Model Overall Dimensions: Table ........................................................................................................12 3 ⁄ 16 '...

-24- G7945/46 Radial Drill Press Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs or alterations or l...

G7945/46 Radial Drill Press -25- 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___D...