Grizzly Industrial G5049Z - Manuals

Page 2 - WARNING; other masonry products.

-2 - G5049Z Combination Sander WARNING Some dust created by power sanding, sawing, grind-ing, drilling, and other construction activities containschemicals known to the State of California to causecancer, birth defects or other reproductive harm.Some examples of these chemicals are: • Lead from lead...

Page 3 - Table Of Contents

G5049Z Combination Sander -1- Table Of Contents PAGE 1. SAFETY ....................................................................................................................2 SAFETY RULES FOR ALL TOOLS ....................................................................2 ADDITIONAL SAFETY INST...

Page 5 - Additional Safety Instructions For Sanders

G5049Z Combination Sander -3- Additional Safety Instructions For Sanders 17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommend-ed accessories. The use of improper acces-sories may cause risk of injury to persons. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or...

Page 6 - Grounding; SECTION 2: CIRCUIT REQUIREMENTS

-4- G5049Z Combination Sander Figure 1. Grounded Outlet Box CurrentCarryingProngs Grounding Blade IsLongest Of the Three Blades Under no circumstances should the groundingpin from any three-pronged plug be removed. If itwill not fit the outlet, have the proper outletinstalled by a qualified electric...

Page 7 - SECTION 3: GENERAL INFORMATION

G5049Z Combination Sander -5- We are proud to bring you the Model G5049ZCombination Sander. The Model G5049Z is partof a growing Grizzly family of fine woodworkingmachinery. When used according to the guide-lines set forth in this manual, you can expectyears of trouble-free, enjoyable operation andp...

Page 8 - Unpacking; Piece Inventory

-6- G5049Z Combination Sander Contents of the Bolt Bag QTY. DESCRIPTION LOCATION 16 5 ⁄ 16 ''-18 x 1 ⁄ 2 '' Carriage Bolts Stand 16 5 ⁄ 16 '' Flat Washers Stand 16 5 ⁄ 16 ''-18 Hex Nuts Stand 4 5 ⁄ 16 ''-18 x 1'' Hex Bolts Stand /Feet 8 5 ⁄ 16 '' Flat Washers Stand /Feet 4 5 ⁄ 16 ''-18 Hex Nuts Stan...

Page 9 - Clean up; Site Considerations

G5049Z Combination Sander -7- Clean up The work table and other unpainted parts of theModel G5049Z are coated with a waxy oil thatprotects them from corrosion during shipment.Remove the protective coating with mineral spir-its and cloth rags. Do not use gasoline or otherpetroleum based solvents beca...

Page 11 - Wiring The Motor

G5049Z Combination Sander -9- Figure 5. Align the center of the drive disc to the centerline of the jack shaft C/L Jackshaft Drive disc Figure 6. 10. Re-install the cover. 5. Mount the motor to the motor mount. Leavethe bolts finger tight for now. 6. Lift the spring loaded side of the jackshaftassem...

Page 12 - Belt Replacement; SECTION 5: ADJUSTMENTS; Belt Tracking

-10- G5049Z Combination Sander 2. Turn the knob approximately 1 ⁄ 4 turn clock- wise to move the belt towards the trackingknob, counter-clockwise to move the beltaway. 3. Turn the machine on and off again quickly tosee if the tracking has improved. If not,repeat step 1. If tracking is improved move ...

Page 13 - Belt Tensioning

G5049Z Combination Sander -11- 3. Tighten hex bolt and run the sander to adjustthe tracking if necessary. 4. Try aggressively sanding a piece of scrapwood. If the tracking is not significantlyaffected and the belt does not slip on thedrum, your belt tension is correct. Belt Tensioning Correct belt t...

Page 14 - Horizontal Sanding; SECTION 6: OPERATIONS; Test Run

-12- G5049Z Combination Sander Horizontal Sanding 1. Turn the sander on and allow the belt toreach full speed. 2. Place the workpiece flat on the belt. Be sureto hold the work securely with both hands.Place one hand at the end of the workpieceto feed it against the rotation of the belt, andone hand ...

Page 16 - SECTION 7: MAINTENANCE; Lubrication; General

-14- G5049Z Combination Sander SECTION 7: MAINTENANCE Lubrication V- Belt Your combination sander is equipped with shield-ed and pre-lubricated ball bearings and requireno lubrication for the life of the bearings. All bear-ings are common sizes and are readily availablefrom a local bearing supply ho...

Page 25 - Machine Data

G5049Z Combination Sander -23- Machine Data GRIZZLY MODEL G5049Z COMBINATION SANDER Design Type .......................................................................................................................... Floor Model Overall Dimensions and Specifications: Base ............................

Page 26 - WARRANTY AND RETURNS

-24- G5049Z Combination Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs or alterations or lac...