Grizzly Industrial G3105 - Manuals

Grizzly Industrial G3105 – Manual in PDF format online.

Manuals:

Manual

Manual Grizzly Industrial G3105

Summary

Page 3 - Table Of Contents

G3105 Combination Sander -1- Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR ALL TOOLS ......................................................................2-3ADDITIONAL SAFETY INSTRUCTIONS FOR SANDERS ......................................4 2. CIRCUIT REQUIREMENTS 110V OPERATION ...................

Page 4 - Safety Instructions For Power Tools; For Your Own Safety Read Instruction

-2- G3105 Combination Sander Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORSAWAY . All children and visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removingstarter keys. 7. DON’T FORCE TOO...

Page 6 - Additional Safety Instructions For Sanders

-4- G3105 Combination Sander Additional Safety Instructions For Sanders No list of safety guidelines can be com-plete. Every shop environment is different.Always consider safety first, as it applies toyour individual working conditions. Usethis and other machinery with caution andrespect. Failure to...

Page 7 - SECTION 2: CIRCUIT REQUIREMENTS; Fusing

G3105 Combination Sander -5- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 15-amp fuse or circuit breaker should be usedwhen fusing this combination sander. Circuitsrated any higher are not adequate to protect themotor from power surges. Equipment returned to us for service that showsevidence of ...

Page 8 - SECTION 3: INTRODUCTION; Commentary

-6- G3105 Combination Sander SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G3105Combination Belt and Disc Sander. The ModelG3105 is part of a growing Grizzly family of finewoodworking machinery. When used accordingto the guidelines set forth in this manual, you canexpect years of t...

Page 9 - NOTICE

G3105 Combination Sander -7- Unpacking This Combination Sander is shipped from themanufacturer in a carefully packed carton. If youdiscover the machine is damaged after you’vesigned for delivery, and the truck and driver aregone, you will need to file a freight claim with thecarrier. Save the contai...

Page 10 - Clean Up; Site Consideration

-8- G3105 Combination Sander Clean Up BENCH LOAD Your G3105 Combination Sander represents arelatively large weight load in a small footprint. Besure that your workbench is adequately rein-forced to support the weight of the sander. WORKING CLEARANCES Working clearances can be thought of as the dis-t...

Page 11 - Overview

G3105 Combination Sander -9- SECTION 4: ASSEMBLY Overview All die-cut metal parts have a sharp edge(called “flashing”) on them after they areformed. This is generally removed at thefactory. Sometimes a bit of flashing mightescape inspection, and the sharp edge maycause cuts or lacerations when handl...

Page 13 - Disc Table Bracket; Disc Table

G3105 Combination Sander -11- Disc Table Bracket The disc table bracket mounts to the left side ofthe sanding unit, below the disc. Use the two hexbolts and washers provided. Tighten securely.See Figure 5. Figure 5. Disc table bracket in place. Disc Table 1. Unscrew the table trunnion guide screwsfr...

Page 14 - SECTION 5: Adjustments; Belt Tension

-12- G3105 Combination Sander SECTION 5: Adjustments Belt Tension A B C Figure 7. Adjustments for tension and tracking. Belt tension is controlled by a spring loaded camshaft. Push the Belt Tensioning Lever (part C, Figure 8) rearward to slacken the belt. Belt Tracking Plug in the machine. Test the ...

Page 15 - SECTION 6: Operations; General Sanding

G3105 Combination Sander -13- SECTION 6: Operations Before you put your Combination Sander intouse, give it a quick inspection. Before inspecting,ensure that the machine is switched off and dis-connected from its power source. 1. Are all fasteners tight? 2. Is the sanding belt properly tracked andte...

Page 16 - Disc Sanding

-14- G3105 Combination Sander Disc sanding is well suited for finishing small flatsurfaces and curved edges. The down (right)side of the disc is the working area. The discmoves fastest and removes the most material atthe outer edge. A miter gauge that fits in the slotin the table is provided. Use it...

Page 17 - SECTION 7: MAINTENANCE; General

G3105 Combination Sander -15- SECTION 7: MAINTENANCE General Shielded and pre-lubricated ball bearings requireno lubrication. As for other items on this machine, such as rollershafts, use an occasional “shot” of light machineoil. Wipe off any sawdust or grit with a clean clothbefore applying light o...

Page 19 - GRIZZLY MODEL G3105 BELT/DISC SANDER; MACHINE DATA

G3105 Combination Sander -17- Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G3105 BELT/DISC SANDER MACHINE DATA SHEET Design Type .................................................................................................... Bench Mode...

Page 20 - DIAGRAMS & PARTS LISTS

-18- G3105 Combination Sander 1 P3105001 ROTOR 2 P3105002 STATOR 3 P6202 BALL BEARING 6202 4 P3105004 MOTOR END BELL 6 P3105006 CAPACITOR 7 P3105007 CAPACITOR CLIP 8 P3105008 BOTTOM COVER 9 P3105009 RUBBER FOOT 10 P3105010 DISC GUARD 11 P3105011 DISC GUARD BRACKET 12 P3105012 SANDING PLATE 13 P31050...

Page 22 - TROUBLESHOOTING

-20- G3105 Combination Sander SYMPTOM Motor will not start. Motor will not start;fuses or circuit break-ers blow. Motor fails to developfull power (power out-put of motor decreas-es rapidly withdecrease in voltage atmotor terminals). Motor overheats. Motor stalls (resultingin blown fuses ortripped c...

Page 23 - NOTES

Page 24 - WARRANTY AND RETURNS

-22- G3105 Combination Sander WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs o...

Page 25 - WARRANTY CARD

G3105 Combination Sander 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt...