Grizzly Industrial G1200 - Manuals

Grizzly Industrial G1200 – Manual in PDF format online.

Manuals:

Manual

Manual Grizzly Industrial G1200

Summary

Page 2 - WARNING; other masonry products.

-B- G1199/G1200 Drill Press WARNING Some dust created by power sanding, sawing, grind-ing, drilling, and other construction activities containschemicals known to the State of California to causecancer, birth defects or other reproductive harm.Some examples of these chemicals are: • Lead from lead-ba...

Page 3 - Table Of Contents

Table Of Contents PAGE 1. INTRODUCTION ........................................................................................................2 SAFETY RULES FOR ALL TOOLS ........................................................................3UNPACKING.................................................

Page 4 - SECTION 1: INTRODUCTION

-2- G1199/G1200 Drill Press Grizzly Imports, Inc. is proud to offer the ModelG1199/G1200 Drill Press. This drill press is a partof Grizzly’s growing family of fine woodworkingand metalworking machinery. When used accord-ing to the guidelines stated in this manual, youcan expect years of trouble-free...

Page 5 - Safety Rules For All Tools

G1199/G1200 Drill Press -3- 12. USE SAFETY GLASSES AND EAR PRO- TECTION. Also use a DUST MASK if the operation is dusty. 13. DO NOT OVERREACH. Keep proper footing and balance at all times. 14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best andsafest performance. Follow instruct...

Page 6 - Unpacking; Piece Inventory

G1199/G1200 Drill Press -4- Unpacking The Model G1199/G1200 Drill press is shippedfrom the manufacturer in a carefully packed car-ton. If you discover the machine is damaged afteryou’ve signed for delivery, please call Customer Service immediately for advice. Save the containers and all packing mate...

Page 7 - Clean up; Site Considerations

G1199/G1200 Drill Press -5- Clean up The column and other unpainted parts of theModel G1199/G1200 are coated with a waxy oilthat protects them from corrosion during ship-ment. Remove the protective coating with miner-al spirits and paper towels. Do not use gasoline orother petroleum based solvents b...

Page 8 - Circuit Requirements

-6- G1199/G1200 Drill Press Circuit Requirements The motor supplied with the G1199/G1200 is a110V single-voltage motor, prewired for 110V.Under normal use, the motor draws approximate-ly 9 amps @ 110V. We recommend using a 15amp circuit breaker or a 15 amp slow blow fusefor 110V operation. This shou...

Page 9 - Beginning Assembly

G1199/G1200 Drill Press -7- Beginning Assembly Most of the Drill Press has been pre-assembledat the factory. The few remaining pieces shouldgo together quickly and easily. Assembly isstraight forward and with just a few tools you cando the entire job quickly and easily. This manualis written for the...

Page 12 - Drill Chuck

-10- G1199/G1200 Drill Press Drill Chuck Figure 9. Drill chuck assembly. The Drill Press chuck and arbor must be mount-ed in the drill press spindle. The arbor has a #6Jacobs Taper on one end and a #2 Morse Taperon the other. The #6 Jacobs Taper fits into thedrill chuck and the #2 Morse Taper fits i...

Page 13 - Speed Change; SECTION 3: ADJUSTMENTS

G1199/G1200 Drill Press -11- Speed Change SECTION 3: ADJUSTMENTS Remember to disconnect the drill press from thepower source before attempting any adjustments. 1. To change speed, loosen the two lock knobs,one on either side of the head. Figure 10. 2. Turn the cam lever so the motor pulley movestowa...

Page 14 - Spindle Adjustments

-12- G1199/G1200 Drill Press To stop the vertical travel of the drill bit at adesired depth, loosen the scale set knob locatedon the feed shaft assembly, rotate the handles tothe desired depth and tighten the scale set knob. Figure 12. To hold a stationary depth, loosen the scale setknob and rotate ...

Page 15 - Chuck Removal

G1199/G1200 Drill Press -13- Figure 15. Figure 14. 4. To tilt the table, loosen the pivot bolt andremove the locator pin ( Figure 15 ). This is done by tightening the nut until the pin isextracted from its hole. Tilt the table to thedesired angle (up to 45°) and re-tighten thepivot bolt. Re-insert t...

Page 16 - SECTION 4: OPERATIONS; Safety Rules

-14- G1199/G1200 Drill Press Caution Always wear ANSI-approved safetyglasses or goggles when operatingequipment — particularly when test-ing new tools or machinery. Do notallow visitors into your workshopwhen testing or operating equipment. SECTION 4: OPERATIONS Safety Rules • The workpiece must be ...

Page 19 - Mortise Attachment

G1199/G1200 Drill Press -17- Figure 18. Mortise Attachment installed. Mortise Attachment The optional Grizzly G1083 Mortise Attachmentwas specifically designed to fit the G1199/G1200Drill Presses. Refer to our current catalog forordering information. Drilling Wood Twist bits, which are intended for ...

Page 20 - SECTION 5: MAINTENANCE; Lubrication; General

-18- G1199/G1200 Drill Press SECTION 5: MAINTENANCE Lubrication Belt Tension Shielded and pre-lubricated ball bearings requireno lubrication for the life of the bearings. In a con-tinuous-use environment, expect the bearings tolast for several years. With intermittent use, bear-ings can be expected ...

Page 26 - WARRANTY AND RETURNS

-24- G1199/G1200 Drill Press Grizzly Imports, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neg-ligence, accidents, repairs or alterations or lack o...

Page 27 - Recommended RPM

G1199/G1200 Drill Press -25- Recommended RPM Drill Cast Diameter Iron Steel Aluminum Wood 1 ⁄ 8 " 1900 2620 2620 2620 3 ⁄ 16 " 1550 1620 2620 2620 1 ⁄ 4 " 990 1350 1550 2620 5 ⁄ 16 " 650 990 1550 1550 3 ⁄ 8 " 600 990 990 1550 7 ⁄ 16 " 510 650 990 990 1 ⁄ 2 " 510 650 650 9...