Grizzly Industrial G1182HW - Manuals

Grizzly Industrial G1182HW – Manual in PDF format online.

Manuals:

Manual

Manual Grizzly Industrial G1182HW

Summary

Page 2 - WARNING; • Arsenic and chromium from chemically treated

WARNING Some dust created by power sanding, sawing, grinding,drilling, and other construction activities contains chemi-cals known to the State of California to cause cancer,birth defects or other reproductive harm. Some examplesof these chemicals are: • Lead from lead-based paints.• Crystalline sil...

Page 3 - Terms and Definitions

G1182 6" Series Jointers -1- G1182 Series Jointers Terms and Definitions G1182ZHW Description G1182HW G1182Z G1182ZX Stand Switch Table Adjustment Motor Dust Collection Weight Cabinet Toggle On / Off Hand Wheels 1 H.P. Chip Chute 215 lbs. Steel Stand Toggle On / Off Hand Wheels 1 H.P. Chip Chute...

Page 4 - Table Of Contents

-2- G1182 6" Series Jointers Table Of Contents PAGE 1. SAFETY WARNINGS ............................................................................................................3SAFETY RULES FOR ALL TOOLS ........................................................................4ADDITIONAL SAFET...

Page 5 - Safety Instructions For Power Tools; For Your Own Safety Read Instruction

G1182 6" Series Jointers -3- Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORSAWAY. All children and visitors should be kept a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removingstarter keys. 7. DO NOT FORCE ...

Page 7 - Additional Safety Instructions For Jointers

G1182 6" Series Jointers -5- No list of safety guidelines can be complete.Every shop environment is different. Alwaysconsider safety first, as it applies to yourindividual working conditions. Use this andother machinery with caution and respect.Failure to do so could result in serious per-sonal ...

Page 8 - SECTION 2: CIRCUIT REQUIREMENTS; Extension Cords

-6- G1182 6" Series Jointers 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 15 amp fuse or circuit breaker should be usedwhen fusing this (tool description). Circuit break-ers rated any higher may not be adequate to pro-tect the circuit from power surges. If you find it necessary to use an ext...

Page 9 - SECTION 3: INTRODUCTION; Commentary

G1182 6" Series Jointers -7- SECTION 3: INTRODUCTION We are proud to offer these four models of theModel G1182 6" Jointer. These machines are partof a growing Grizzly family of fine woodworkingmachinery. When used according to the guide-lines set forth in this manual, you can expectyears of ...

Page 10 - NOTICE

-8- G1182 6" Series Jointers Unpacking Piece Inventory NOTICE A full parts list and breakdown can be foundtoward the end of this manual. For easierassembly, or to identify specific parts,please refer to the detailed illustrations atthe end of the manual. Model G1182HW (Figure2A) • Jointer Assemb...

Page 12 - Site Considerations; Clean Up

-10- G1182 6" Series Jointers Site Considerations FLOOR LOAD Your Model G1182 series jointer represents amoderate weight load in a small footprint. Mostcommercial or home shop floors should be suffi-cient to carry the weight. If you question thestrength of your floor, you may wish to check witha...

Page 13 - Beginning Assembly; Stand

G1182 6" Series Jointers -11- SECTION 4: ASSEMBLY Beginning Assembly Most of your Model G1182 6'' Jointer has beenassembled at the factory, but some parts must beassembled or installed after delivery. We haveorganized the assembly process into steps.Please follow along in the order presented her...

Page 15 - Jointer to Stand

G1182 6" Series Jointers -13- 6. The power switch is already installed on theright hand panel of the stand. To complete thewiring, it is first necessary to remove theswitch assembly from the stand. Remove thetwo Phillips ® head screws holding the metal mounting plate to the stand. The entire swi...

Page 16 - Fence

-14- G1182 6" Series Jointers Figure 8. Motor mounts inside dust chute. Figure 9. Pulley and V-belt alignment. 1. Loosen the motor mount bolts located insidethe dust chute and slide the motor up untilyou can attach the V-Belt to the pulleys. See Figure 8. V-Belt Fence 2. Allow the weight of the ...

Page 19 - Table Gibs; SECTION 5: ADJUSTMENTS; Knives

G1182 6" Series Jointers -17- Table Gibs SECTION 5: ADJUSTMENTS The function of the gibs are to allow preciseadjustment of the table movement along thedovetail ways. Adjustment of the gib will dictatehow easy it will be to move the tables up anddown with the levers or handwheels. To adjustgibs: ...

Page 21 - Outfeed Table

G1182 6" Series Jointers -19- ADJUSTMENTS USING SPRINGS. The knives are locked into the cutterhead with wedge-type gibs and gib bolts. Jack screws under the knivesmay be substituted with springs to help in the settingprocess. When using springs, it is advised that the jackscrews be removed. To r...

Page 22 - Infeed Table

-20- G1182 6" Series Jointers Figure 18. Illustrates the use of a straightedge to ensure proper outfeed adjustment. 4. Loosen the table lock handle and raise orlower the table with the lever until the straight-edge barely touches one of the knives. Rockthe cutterhead to ensure that the blade is ...

Page 23 - 0° Fence Stop; 5° Fence Stop

G1182 6" Series Jointers -21- 1. Place a square on the outfeed table fairlyclose to the cutterhead. See Figure 20 . Figure 20. Use of square to align fence. 2. Loosen the fence lock handle and the check-nut on the positive stop bolt. Turn the boltagainst the tab until the fence contacts theedge ...

Page 25 - SECTION 6: OPERATIONS; Test Run

G1182 6" Series Jointers -23- SECTION 6: OPERATIONS Once assembly is complete and adjustments aredone to your satisfaction, you are ready to testrun the machine. Turn on the power supply at the main panel.Press the START button. Make sure that your fin-ger is poised on the STOP button, just in c...

Page 26 - Edge Joining

-24- G1182 6" Series Jointers The purpose of edge jointing is to produce a fin-ished, flat-edged surface that is suitable for join-ery or finishing. It is also a necessary step prior toripping stock to width on a table saw or radial armsaw. 1. Make sure the fence is set to 90°. Doublecheck it no...

Page 28 - SECTION 7: MAINTENANCE; Lubrication

-26- G1182 6" Series Jointers SECTION 7: MAINTENANCE Lubrication V-Belt General Tables Regular periodic maintenance on your ModelG1182 Jointer will ensure its optimum perfor-mance. Make a habit of inspecting your jointereach time you use it. Check for the following con-ditions and repair or repl...

Page 30 - MACHINE DATA

-28- G1182 6" Series Jointers Design Type ......................................................................................................Floor Model Capacities: Maximum Depth of Cut .............................................................................................. 1 ⁄ 2 " ...

Page 31 - MAIN TABLES

G1182 6" Series Jointers -29- 33 32 17 29 30 34 31 11 16 12 10 06 06 09 11 16 13 05 28 26 04 25 03 09 16 15 14 08 28 27 1 10 02 20 21 22 23 24 18 18A 09 08 09 12 07 07 07 06 05A 25 13 01 PG1182001 BASE 01 PG1182HW001 BASE (TYPE HW) 02 PG1182002 INFEED TABLE 02 PG1182HW002 INFEED TABLE (TYPE HW) ...

Page 33 - FENCE

G1182 6" Series Jointers -31- 108 101 102 110 111 109 103 124 102 106 107 104 105 105 104 115 112 113 116 120 119 114 121 123 122 122 130 129 128 125 117 118 123 126 126 127 101 PG1182101 FENCE 102 PG1182102 PIVOT STUD 103 PG1182103 FENCE HINGE 104 PG1182104 SPECIAL SCREW 105 PN08 HEX NUT 3 ⁄ 8 ...

Page 34 - CUTTERHEAD

-32- G1182 6" Series Jointers 202 203 208 207 206 213 212 211 201 205 204 210 209 215 214 216 207 206 217 217 REF PART # DESCRIPTION 201 PG1182201 CUTTERHEAD 202 G1188 KNIVES, SET OF THREE 203 P1021103 SPRING 204 PG1182204 KNIFE GIB 205 P1017117 GIB BOLT 206 PN11 HEX NUT 3 ⁄ 8 "-24 207 PLW04...

Page 35 - STAND FOR JOINTER MODEL G1182HW

G1182 6" Series Jointers -33- 311 310 303 316 301 315 314 313 312 319 305 310 311 318 317 307 309A 310 311 321 311 310 304 307 306 320 302 325 326 316 315 310 311 311 310 322B 330 308 322-1 323A REF PART # DESCRIPTION 301 PG1182301 BASE PANEL 302 PG1182302 RIGHT STAND SUPPORT 303 PG1182303 LEFT ...

Page 36 - HANDWHEEL ASSEMBLY FOR

-34- G1182 6" Series Jointers 401 403 406 403 407 408 409 410 411 412 404 405 402 413 REF PART # DESCRIPTION 401 PB19 HEX BOLT 1 ⁄ 4 "-20 X 1 ⁄ 2 " 402 PW06 FLAT WASHER 1 ⁄ 4 " 403 PG1182HW403 BRONZE FLAT WASHER 1 ⁄ 2 " 404 PB03 HEX BOLT 5 ⁄ 16 "-18 X 1" 405 PW07 FLAT WAS...

Page 37 - PEDESTAL MOUNTED SWITCH FOR

G1182 6" Series Jointers -35- PEDESTAL MOUNTED SWITCH FOR JOINTER MODEL G1182ZX REF PART # DESCRIPTION 414 PG1182ZX414 SELF TAPPING SCREW 415 PB02 HEX BOLT 1 ⁄ 4 -20 X 5 ⁄ 8 " 416 PW06 FLAT WASHER 1 ⁄ 4 " 417 PN05 1 ⁄ 4 "-20 NUT 418 PG1182ZX418 SWITCH HOUSING 419 PG1182ZX419 PEDESTAL...

Page 38 - STAND FOR JOINTER MODEL G1182ZX

-36- G1182 6" Series Jointers 426 427 428 429 421 STAND FOR JOINTER MODEL G1182ZX REF PART # DESCRIPTION 426 PB22 HEX BOLT 3 ⁄ 8 "-16 x 1" 427 PN03 HEX NUT 3 ⁄ 8 ''-16 428 PG1182ZX428 HEAVY-DUTYCABINET STAND 429 PW02 FLAT WASHER 3 ⁄ 8 " These parts are exclusive to theModel G1182ZX s...

Page 39 - TROUBLESHOOTING

G1182 6" Series Jointers -37- TROUBLESHOOTING SYMPTOM Motor will not start. Motor will not start; fuses orcircuit breakers blow. Motor overheats. Motor stalls (resulting inblown fuses or tripped cir-cuit). Machine slows when oper-ating. Loud, repetitious noise com-ing from machine Machine is lou...

Page 40 - WARRANTY AND RETURNS

-38- G1182 6" Series Jointers Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs or alterations or ...

Page 41 - WARRANTY CARD

G1182 6" Series Jointers -39- CUT ALONG DOTTED LINE 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Ban...