Grizzly Industrial G1029Z - Manuals

Page 3 - WARNING; • Arsenic and chromium from chemically treated

WARNING Some dust created by power sanding, sawing, grind-ing, drilling, and other construction activities containschemicals known to the State of California to causecancer, birth defects or other reproductive harm.Some examples of these chemicals are: • Lead from lead-based paints.• Crystalline sil...

Page 4 - Table Of Contents

Table Of Contents PAGE 1. SAFETY SAFETY INSTRUCTIONS FOR POWER TOOLS ..................................................2ADDITIONAL SAFETY INSTRUCTIONS FOR DUST COLLECTORS ....................4 2. CIRCUIT REQUIREMENTS G1028Z ...............................................................................

Page 6 - Safety Instructions For Power Tools Cont.

G1028Z/G1029 Dust Collector -3- 9. USE PROPER EXTENSION CORD.Make sure your extension cord is in goodcondition. Conductor size should be inaccordance with the chart below. Theamperage rating should be listed on themotor or tool nameplate. An undersizedcord will cause a drop in line voltageresulting ...

Page 8 - SECTION 2: CIRCUIT REQUIREMENTS

G1028Z/G1029 Dust Collector -5- SECTION 2: CIRCUIT REQUIREMENTS G1028Z Wiring The G1028Z Dust Collector is pre-wired for 110V,but can be rewired for 220V. Refer to the wiringdiagram included with this manual for instruction.Do not attempt to rewire the motor if the diagramis missing. Contact the app...

Page 10 - SECTION 3: INTRODUCTION; Commentary

G1028Z/G1029 Dust Collector -7- SECTION 3: INTRODUCTION Grizzly Industrial, Inc. is proud to offer the ModelG1028Z/G1029 Dust Collector. These dust col-lectors are a part of Grizzly’s growing family offine machinery. When used according to theguidelines set forth in this manual, you can expectyears ...

Page 14 - Collector Body

G1028Z/G1029 Dust Collector -11- Figure 3. Mounting collector to base. Figure 4. Mounting outlet to collector body. Collector Body The collector body includes the fan assembly,switch, and motor which are preassembled at thefactory. Set the collector body on top of the baseplate so the intake portion...

Page 15 - Collector

-12- G1028Z/G1029 Dust Collector Figure 6. Mounting collector to brackets. Collector The collector attaches to each support bracket.The inside of the collector is funnel shaped anddirects the air around in a cyclone motion. Makesure that the inside taper (funnel) is faced down-ward and the collector...

Page 17 - Inlet

-14- G1028Z/G1029 Dust Collector Figure 10. Tightening steel band. 3. Slip the steel band around the bag and tight-en down as shown in Figure 10. Inlet Press the “Y” inlet onto the inlet cover flange asshown in Figure 11. The inlet is secured to thecollector body by a press-on fit. Figure 11. Instal...

Page 18 - SECTION 5: Designing The System

G1028Z/G1029 Dust Collector -15- Material Selection General You have many choices regarding main line andbranch line duct material. In most commercialworkshops, the main line and branch lines areusually metal duct. Flexible hose is then used toconnect each machine to the branch lines. In thecase of ...

Page 19 - System Grounding

-16- G1028Z/G1029 Dust Collector Since plastic hose is abundant, relatively inexpen-sive, easily assembled and air tight, it is a verypopular material for conveying dust from wood-working machines to the dust collector. We rec-ommend using flexible hose (flex-hose) to con-nect the woodworking machin...

Page 21 - Design Suggestions

-18- G1028Z/G1029 Dust Collector The best way to plan your new system is to drawa bird’s eye view (as shown in Figure 14) of yourshop and sketch the following: 1. Your desired location of the dust collector,usually in a corner or along a wall. 2. The location of each machine in the system. 3. The lo...

Page 22 - SECTION 6: OPERATIONS; Test Run

G1028Z/G1029 Dust Collector -19- SECTION 6: OPERATIONS Once assembly is complete and adjustments aredone to your satisfaction, you are ready to test runthe machine. Turn on the power supply at the main panel.Press the START button. Make sure that your fin-ger is poised on the STOP button, just in ca...

Page 23 - SECTION 7: MAINTENANCE; Lubrication; General

-20- G1028Z/G1029 Dust Collector SECTION 7: MAINTENANCE Lubrication Bag Cleaning Since all bearings are shielded and permanentlylubricated, simply leave them alone until theyneed to be replaced. Do not lubricate them. Regular periodic maintenance on your ModelG1028Z/G1029 Dust Collector will ensure ...

Page 25 - WIRE DIAGRAM

-22- G1028Z/G1029 Dust Collector WIRE DIAGRAM WHITE RED BLACK YELLOW MOTOR WIRES 110 VOLT GREEN (GROUND) TO 110 VOLTPOWER SUPPLY RED WHITE BLACK YELLOW MOTOR WIRES 220VOLT GREEN (GROUND) TO 220 VOLTPOWER SUPPLY NOTE: THE WIRES FROM THE POWER SUPPLY, BESIDES THE GREEN GROUND WIRE, ARE INTERCHANGEABLE...

Page 29 - WARRANTY AND RETURNS

-26- G1028Z/G1029 Dust Collector Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser fromthe date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs or alterations or la...

Page 30 - WARRANTY CARD

10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt S...