Grizzly Industrial G1013 - Manuals

-4- G1013 Combination Sander Additional Safety Instructions For Sanders No list of safety guidelines can be com-plete. Every shop environment is different.Always consider safety first, as it appliesto your individual working conditions. Usethis and other machinery with caution andrespect. Failure to...

G1013 Combination Sander -5- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 15-amp fuse or circuit breaker should be usedwhen fusing this combination sander. Circuitbreakers rated any higher are not adequate toprotect the circuit from power surges. Fusing If you find it necessary to use an extensi...

-6- G1013 Combination Sander SECTION 3: Introduction We are proud to offer the Grizzly Model G1013Combination Sander. The Model G1013 is part ofa growing Grizzly family of fine woodworkingmachinery. When used according to the guide-lines set forth in this manual, you can expectyears of trouble-free,...

G1013 Combination Sander -7- Unpacking This Combination Sander is shipped from the manufacturer in a carefully packed carton. If youdiscover the machine is damaged after you’vesigned for delivery, and the truck and driver aregone, you will need to file a freight claim with thecarrier. Save the conta...

G1013 Combination Sander -9- Clean Up BENCH LOAD Your Model G1013 Combination Sander repre-sents a relatively large weight load in a small foot-print. Be sure that you workbench is adequatelyreinforced to support the weight of the sander. WORKING CLEARANCES Working clearances can be thought of as th...

-14- G1013 Combination Sander SECTION 5: Adjustments Figure 16. Adjusting rear axle. 4. Move hands away from 8'' disc. 5. Plug sander into power and turn machine onand off quickly. Inspect tracking. 6. Repeat steps 1-5 until the belt is centered onthe rollers. If the belt tracks properly on the two ...

G1013 Combination Sander -15- Once you have turned off the switch and discon-nected the sander from its power source: 1. Loosen the hex nut as shown in Figure 18. 2. Tilt the table to the desired position. 3. Tighten the hex nut. Belt Table Tilt Figure 18. Belt table in tilted position. Once you hav...

-16- G1013 Combination Sander Once you have turned off the switch and discon-nected the sander from its power source: 1. Remove the Sanding Disc Table. 2. Peel off the old Sanding Disc. Remove thebacking from the new Disc, center it andpress it firmly into place. 3. It may become necessary to remove...

G1013 Combination Sander -17- SECTION 6: Operations Before you put your Combination Sander intouse, give it a quick inspection with the machineswitched off and disconnected from its powersource. 1. Are all fasteners tight? 2. Is the sanding belt properly tracked and ten-sioned? 3. Rotate disc slowly...

G1013 Combination Sander -19- Figure 21. Belt arrangement for inside sanding. To sand or grind an interior work area, the sand-ing belt must be fed through the workpiece andremounted on its rollers. Depending on yourapplication, you may either remove the platen orkeep it in place. 1. Remove the Belt...

-20- G1013 Combination Sander SECTION 7: MAINTENANCE General Table Your combination sander is equipped with shield-ed and pre-lubricated ball bearings that requireno lubrication for the life of the bearings. All bear-ings are common sizes and are readily availablefrom a local bearing supply house or...

G1013 Combination Sander -21- Maintenance Performed Approximate Hours Of Use Maintenance Notes Date

G1013 Combination Sander -23- Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type .................................................................................................... Bench Model Overall Dimensions: Base .............

G1013 Combination Sander -25- PARTS LIST 1 P1013001 GUARD BACK 2 PWN01 WING NUT 10-24 3 P1013003 TOP PIVOT BRACKET 4 P1013004 KNOB BOLT 1 ⁄ 4 -20 X 1" 5 PEC03M E-CLIP 10mm 6 P1013006 UPPER WHEEL SHAFT 7 P1013007 SPECIAL CLIP 8 P6200 BEARING 6200-2RS 9 P1013009 TOP WHEEL 10 PR01M SNAP RING 10mm 1...

-26- G1013 Combination Sander WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs o...

G1013 Combination Sander -27- CUT ALONG DOTTED LINE 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw...