Grizzly Industrial G0533 - Manuals

Grizzly Industrial G0533 – Manual in PDF format online.

Manuals:

Manual

Manual Grizzly Industrial G0533

Summary

Page 3 - Table of contents

Table of contents iNTRODUcTiON ............................................... 2 Manual accuracy ........................................... 2Contact info.................................................... 2data sheet ..................................................... 3identification ..............

Page 4 - iNTRODUcTiON; Manual Accuracy; contact info

-2- Model g0533 (Mfg. since 3/11) iNTRODUcTiON We are proud to offer this manual with your new machine! We've made every effort to be exact with the instructions, specifications, drawings, and photographs of the machine we used when writing this manual. However, sometimes we still make an occasional...

Page 5 - Data Sheet; MACHINE DATA

Model g0533 (Mfg. since 3/11) -3- Data Sheet The information contained herein is deemed accurate as of 4/19/2011 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G...

Page 7 - identification

Model g0533 (Mfg. since 3/11) -5- A. spray Booth Frame B. air Filter indicator c. First stage Filter D. right Curtain E. Work table leg f. Work table G. support Bar H. left Curtain i. top Curtain J. Motor identification figure 1. g0533 identification. h i J a B C d e F g

Page 8 - NOTICE; Safety instructions for Machinery

-6- Model g0533 (Mfg. since 3/11) For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance...

Page 11 - SEcTiON 2: POWER SUPPLY

Model g0533 (Mfg. since 3/11) -9- SEcTiON 2: POWER SUPPLY Availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize th...

Page 12 - Needed for Set Up; Unpacking

-10- Model g0533 (Mfg. since 3/11) SEcTiON 3: SET UP the following items are needed to complete the set up process, but are not included with your machine: DEScRiPTiON Qty • assistants ....................................................2 • hoist ........................................................

Page 13 - inventory

Model g0533 (Mfg. since 3/11) -11- inventory Shipping inventory (figure 2) Qty A. spray Booth .................................................1 B. Curtain (right) .............................................1 c. Connector Bars ...........................................2 D. air Filter indicator (M...

Page 14 - Hardware Recognition chart

-12- Model g0533 (Mfg. since 3/11) Hardware Recognition chart

Page 15 - Exhaust fan; Site considerations

Model g0533 (Mfg. since 3/11) -13- To install the exhaust fan housing: 1. place the inlet gasket over the exhaust fan inlet. Exhaust fan floor Load Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some floors may require additional reinforcement to support...

Page 16 - curtains

-14- Model g0533 (Mfg. since 3/11) Outlet To install the exhaust fan outlet: 1. Place the outlet gasket and outlet over the exhaust fan, and secure with (10) 5 ⁄ 16 "-18 x 1" hex bolts, 20 flat washers, and 10 hex nuts, as shown in figure 5. figure 5. installing outlet. Support Bar To instal...

Page 17 - Work Table

Model g0533 (Mfg. since 3/11) -15- 5. insert the sockets on the top curtain into the connector bars, as shown in figure 10. figure 10. top curtain attached to connector bar. 2. repeat Step 1 with the right curtain. 3. Fasten each curtain brace to the top cover with four 5 ⁄ 16 "-18 x 3 ⁄ 4 hex b...

Page 18 - filters; Ducting

-16- Model g0533 (Mfg. since 3/11) 2. Make sure the work table opens and closes smoothly. 3. reach under the work table and fully extend the two support legs. 4. lock the latches on the bottom of each cur- tain into the work table. 2. install six second-stage filters above and below the middle brace...

Page 19 - Air filter indicator

Model g0533 (Mfg. since 3/11) -17- Air filter indicator To install the air filter indicator: 1. Mount the manometer to the side of the spray booth by threading the M4 x 45 tap screws into the pre-drilled holes ( figure 15 ). 2. Adjust the manometer so the built-in level reads level ( figure 15 ). 3....

Page 20 - SEcTiON 4: OPERATiONS; filter indicator

-18- Model g0533 (Mfg. since 3/11) SEcTiON 4: OPERATiONS Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Loose hair and cloth- ing could get caught ...

Page 22 - SEcTiON 5: MAiNTENANcE

-20- Model g0533 (Mfg. since 3/11) SEcTiON 5: MAiNTENANcE Always disconnect power to the machine before performing maintenance. failure to do this may result in serious person- al injury. Schedule how often you perform maintenance checks depends upon the material type and amount being sprayed. Check...

Page 23 - Troubleshooting

Model g0533 (Mfg. since 3/11) -21- SEcTiON 6: SERvicE Troubleshooting SYMPTOM POSSiBLE cAUSE POSSiBLE SOLUTiON too little airflow in booth. 1. the filter is dirty. 2. obstructions exist in front of the filters. 3. Filters do not meet design specifications. 4. Fan is dirty. 5. Filters not installed c...

Page 25 - Main Parts Breakdown

Model g0533 (Mfg. since 3/11) -23- 1A 1V2 1-1V2 1-2 1-3V2 1-4 1-5 2 3 4V2 4-1 4-2 4-3 4-4 4-5 5 5-1 5-2 5-3 5-4 5-5 5-6 5-7 6 7 8 9 10 11 11-1 11-2 11-3 11-4 11-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 11-15 11-16 11-17 11-18 11-19 11-20 11-21 11-22 11-23 11-24 11-25 11-26 11-27 11-28 12 ...

Page 26 - Main Parts List

-24- Model g0533 (Mfg. since 3/11) REF PART # DESCRIPTION REF PART # DESCRIPTION 1AV2 P0533001AV2 BLOWER HOUSING ASSY V2.03.11 11-20 P0533011-20 SIDE FILTER CASE SUPPORT 1V2 P0533001V2 BLOWER HOUSING V2.03.11 11-21 PHTEK34 TAP SCREW 1/4 X 1/2 1-1V2 P0533001-1V2 IMPELLER 12" V2.03.11 11-22 PN05 H...

Page 27 - Safety Label Placement and Parts List

Model g0533 (Mfg. since 3/11) -25- Safety Label Placement and Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 35 PLABEL-11 SAFETY GLASSES VL 43 G8589 GRIZZLY NAMEPLATE-LARGE 36 PLABEL-12A READ MANUAL VL 44 P0532074 NOTICE FILTERS LABEL 37 P0532068 EXPLOSION HAZARD LABEL 45 PLABEL-14 ELECTRI...

Page 29 - WARRANTY CARD

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

Page 32 - ORDER

Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ ORDER 24 HOURS A DAY! 1-800-523-4777 Visit Our Website Today For Current Specials!