Grizzly Industrial G0464 - Manuals

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 4 - SECTION 1: SAFETY Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates a potentially hazardous situation which, if not avoi...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 7 - This machine must have a ground prong in the plug to help ensure that it is grounded. DO NOT remove ground prong from plug to fit into a two-pronged outlet! If the plug will not fit the outlet, have the proper outlet installed by a qualified ...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 8 - Extension Cords The use of extension cords can cause power loss and overheating in air com-pressors. When possible, locate the air compressor where it can be plugged into an outlet without the use of an extension cord, and use an additional a...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 10 - Placement Do not place the compressor next to flammable liquids or gas! The com-pressor motor and air supply pipe can reach high temperatures and cause the flammable gas to ignite. Keep work area clear from flammable gas when using the compr...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 11 - Operation Safety SECTION 4: OPERATIONS Long term exposure to this machine may cause hearing loss. To protect your hearing, always wear ANSI approved ear protection when operat-ing this air compressor. Operating this equipment has the potenti...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 12 - 6. Close the drain valve ( Figure 5 ) to allow the tank to build up pressure. 7. Check the tank pressure gauge ( Figure 6 ) to see that the tank pressure climbs to approximately 115-120 PSI (around 8 BAR), then automatically turns OFF . Note...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 13 - When choosing air tools, consider the amount of air used (cubic feet per min-ute or CFM) by the tool. Nailers and staple guns have a low CFM requirement because they use air in short bursts. A paint sprayer or a pneumatic grinder uses a more...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 14 - Always disconnect the air hose from tools whenever not in use or while servicing ! During maintenance, a tool connected to air may operate accidentally, causing serious per-sonal injury! When storing your air compressor, fol-low these guidel...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 15 - SECTION 5: MAINTENANCE Schedule For optimum performance from your machine, follow this maintenance sched-ule and refer to any specific instructions given in this section. Daily 1. Check the oil level! Use the sight glass on the crankcase to ...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 16 - Monthly After the first 50 working hours or 30 days, perform the following maintenance: 1. Change the oil in the air compressor pump as described in Changing Oil on Page 19 . Quarterly After every 300 working hours or 3 months, perform the f...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 17 - SECTION 6: SERVICE This section is provided for your convenience—it is not a substitute for the Grizzly Service Department. If you need help troubleshooting, replacing parts, or you are unsure of how to perform the procedures in this section...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 20 - Fixing Air Leaks Air leaks will cause low air output and increase the time the compressor must run. To find air leaks: 1. Turn the compressor OFF when the tank is fully pressurized and unplug the compressor. 2. Listen for the sound of air to...

Model G0464/G0465/G0467/G0468/G0470 Air Compressors - 21 - The pressure switch has been factory set for the highest PSI that is safe for this compressor. The pressure switch ensures the pump will shut OFF when the air compressor tank reaches maximum PSI. Pressure Switch Figure 16. Pressure adjustmen...

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz...

WARRANTY CARD Name _________________________________________________________________Street _________________________________________________________________City _______________________ State _________________________ Zip _________Phone # ____________________ Email ________________________ Invoice # ...

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here